|
Nokia X7 RM-659 не включается после прошивки RM-707
Произошла такая история принесли Nokia X7 прошить на русский язык стояла прошивка 22.8 я обрадоватлся и прошил 025.007... после прошивки апарат не зашол в Local mode после вышла надпись Phone start-up ailed.Contact the retailer... Но когда подумав что что то не так я прочила что с такой прошивкой 22.8 это rm-659 а для рст апараты выходят с rm-707... Получается я прошил телефон rm-659 на rm-707 и в конечном итоге убил возвожно сертификаты... потом пробоват опять прошить на rm-659 с прошивкой 22.8 но никакого результата нет... пробоват прошивать и Cyclone box и MX-Key и Best и UFS и JAF вто же время прошивал через USB хотел поставить галку Dongreit не получается кроме Jaf... А вот еще что интересно когда сохранял RPL через BEST imei он показал полную что и радует...возможно ли поднять тело USB кобелем или нодо обязательно открывать.. просто телефону 4 дня и он совсем новый....
Вот Лог через BEST лог как сохранял RPL:Connect phone on selected interface...
Backup Certificates now... Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- Connection opened successfully Waiting for communication response... [BB5 FLASH]: Bootrom Ok! ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 06D0011957A70344D5C803B7046F9F58DA450C32 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.34.0 Processing RAWLOADER... FLIC : 006800EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.34.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:02 Reopening the connection... Waiting for response: 30 Waiting for response: 29 ADL: Check mode Select ASIC [C900] PAPUBkeys : 9A17C4A57D80D29519AAEF45209AD2F5CF4AD9E9 ADL: Reading certificates... Reading NPC certificate... IMEI : 357899040194015 Reading CCC certificate... Reading HWC certificate... Reading R&D certificate... Reading VARIANT certificate... Reading PARTNERC certificate... Reading MDM_KEYS certificate... Cert Read done! ADL: Reading certificates done! :) ADL: Close_Session Content: 000300000000000000000000000000 ADL: Reboot Wait, reconneting... - > Phone not found... :( - > CertRead failed : phone was not bootup - > Connection/SW/HW problem, try bootup manually NPC Certificate saved... CCC Certificate saved... HWC Certificate saved... RPL saved : c:\InfinityBox\BEST\Backup\Cert\357899040194015_CRT_2nd.rpl Phone disconected! :confused: |
Re: Nokia X7 нет включается
Ну что же. Приступим к оживлению.
Прежде всего приложите все Бэкапы которые удалось сделать (RPL, PM). Исходя из них, я напишу - что делать дальше. |
Re: Nokia X7 нет включается
Вложений: 1
Pm не могу представить так как аппарат не включается в вот rpl пожалуйста
|
Re: Nokia X7 нет включается
Цитата:
Для полного восстановления этого SL3 телефона без заказа RPL, нужна ещё SLD DATA в формате RPL или 120 и 308 поля PM. Есть ещё один вариант сейчас, в таком состоянии телефона, вытащить SLD, точнее PM, если вы не стирали телефон. Но скорее всего SLD и PM уже повреждены при записи SW не соответствующего RM, и толку от них не будет. До самой первой прошивки вы не сохраняли PM или Full RPL ? |
Re: Nokia X7 нет включается
А как слить PM от туда я незнаю? телефон же не заходит в Local mode... да и бекапы я не делал недумал что так получится ктож перед прошивкой сохраняет бекапы хотя понимаю нужно делать ... вообщето правильно малоли что может быть с ним... но это будет мне уроком... и что мне делать на данный момент?
|
Re: Nokia X7 нет включается
Цитата:
- Записываем (соответствующее железу) полное SW (как вы пишете это) RM-659 самой последней версии - Стираем только NPC Код:
в BEST |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Сделал как вы сказали да Вышел local mode но imei 123456.......?
вот лог:Connect phone on selected interface...
Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- Connection opened successfully Waiting for communication response... [BB5 FLASH]: Bootrom Ok! ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 06D0011957A70344D5C803B7046F9F58DA450C32 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.34.0 Processing RAWLOADER... FLIC : 006800EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.34.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:02 Reopening the connection... Waiting for response: 30 Waiting for response: 29 ADL: Check mode Select ASIC [C900] PAPUBkeys : 9A17C4A57D80D29519AAEF45209AD2F5CF4AD9E9 ADL: Preparing for erase certificates... Erase NPC... Ok ADL: Erase Flash certs done! :) ADL: Close_Session Content: 000300000000000000000000000000 ADL: Reboot Done! Phone disconected! Connect phone on selected interface... Phone found! Series 60 Device detected! read info... - Ok Phone disconected! |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
Теперь читаем full PM и Full RPL и выкладываем тут. |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Вложений: 2
Вот я слил PM и RPL
вот лог моей процедуры:Connect phone on selected interface...
Core version : 1.30 Rev : 1.1 Selected FlashSettings : Manual -> File : RM-659_022.008_241.01_default_79.92.2011.21.uda.fpsx not found! Check it! Check FlashFiles, Please, wait... Files Set for Flashing : MCU : RM-659_022.008_79.92_prd.core.fpsx PPM : RM-659_022.008_31.01_NAM_79.92_prd.rofs2.fpsx PPM2 : RM-659_022.008_241.01_default_79.92.2011.21_prd.rofs3.fpsx Flashing phone now... Check files done... -> SWversion check skipped : Dead mode selected Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- -------BOOT BREAKED BY USER------- -> Phone not found.. :( -> Boot fail... Flashing failed... Core version : 1.30 Rev : 1.1 Selected FlashSettings : Manual Check FlashFiles, Please, wait... Files Set for Flashing : MCU : RM-659_022.008_79.92_prd.core.fpsx PPM : RM-659_022.008_31.01_NAM_79.92_prd.rofs2.fpsx PPM2 : RM-659_022.008_241.01_default_79.92.2011.21_prd.rofs3.fpsx Flashing phone now... Check files done... -> SWversion check skipped : Dead mode selected Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- -> Phone not found.. :( -> Boot fail... Flashing failed... Phone found! Series 60 Device detected! read info... - Ok Phone disconected! Connect phone on selected interface... Phone found! Series 60 Device detected! read info... - Ok Phone disconected! Connect phone on selected interface... Phone found! Series 60 Device detected! read info... - Ok Phone disconected! Connect phone on selected interface... Phone found! Series 60 Device detected! read info... - Ok Core version : 1.30 Rev : 1.1 Selected FlashSettings : Manual -> File : RM-659_022.008_241.01_default_79.92.2011.21.uda.fpsx not found! Check it! Check FlashFiles, Please, wait... Files Set for Flashing : MCU : RM-659_022.008_79.92_prd.core.fpsx PPM : RM-659_022.008_31.01_NAM_79.92_prd.rofs2.fpsx PPM2 : RM-659_022.008_241.01_default_79.92.2011.21_prd.rofs3.fpsx Flashing phone now... Check files done... -> Check SW version... FlashFile version : 022.008 Phone version : 022.008 -> Check SW version : Reflash -> Downgrade not need, disable downgrade Backup CRT308 data... CRT308 Backup Created SLx Simlock Data read ... ok SL3 Simlock Sign read ... ok WMDRM read ... ok Check communication with phone.... ADL req restart Communication verify done... Preparing... Gathering phone info... Check communication with phone... Batery valtage : 3745 mV -> Batery voltage less, than 3,8V (3745mV). Continue at user risk Reboot.... Connection opened successfully Waiting for communication response... [BB5 FLASH]: Bootrom Ok! ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 06D0011957A70344D5C803B7046F9F58DA450C32 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.34.0 Processing RAWLOADER... FLIC : 006800EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.34.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:02 Reopening the connection... Waiting for response: 30 Waiting for response: 29 ADL: Check mode Select ASIC [C900] PAPUBkeys : 9A17C4A57D80D29519AAEF45209AD2F5CF4AD9E9 ADL: phone is in flash mode Backup enabled, will read all certificates... Reading NPC certificate... IMEI : 000000000000000 Reading CCC certificate... Reading HWC certificate... Reading R&D certificate... Reading VARIANT certificate... Reading PARTNERC certificate... Reading MDM_KEYS certificate... Cert Read done! CCC Certificate saved... HWC Certificate saved... SimLock Data saved... SimLock Key saved... WMDRM_PD Data saved... RPL saved : c:\InfinityBox\BEST\Backup\Cert\000000000000000.rpl ===Flashing [MCU]=== Erase : Processing RM-659_022.008_79.92_prd.core.fpsx Partitioning.... Partitioning Ok... Erasing.... Erasing Ok... TIME : Erase time : 00:00:02 Write : Processing RM-659_022.008_79.92_prd.core.fpsx CMT: Writing Hash CERT [ADA] CMT: Writing Hash CERT [KEYS] CMT: Writing Hash CERT [PRIMAPP] CMT: Writing Hash CERT [RAP3NAND] CMT: Writing Hash CERT [SOS+PMML] CMT: Writing Hash CERT [PASUBTOC] CMT: Writing Hash CERT [PAPUBKEYS] CMT: Writing Hash CERT [GENIO_INIT] CMT: Writing Hash CERT [SOS*UPDAPP] CMT: Writing Hash CERT [SOS*DSP0] CMT: Writing Hash CERT [LDSP] CMT: Writing Hash CERT [SOS*ISASW] CMT: Writing Hash CERT [SOS+CORE] CMT: Writing Hash CERT [SOS+ROFS1] Total writen 505 blocks TIME : Write time : 00:00:14 MCU Write done ADL: Request programm status NAND status : 00000000 / 00000000 / 00000000 ===Flashing [PPM]=== Erase : Processing RM-659_022.008_31.01_NAM_79.92_prd.rofs2.fpsx Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing RM-659_022.008_31.01_NAM_79.92_prd.rofs2.fpsx CMT: Writing Hash CERT [SOS+ROFS2] Total writen 186 blocks TIME : Write time : 00:00:05 PPM Write done ADL: Request programm status NAND status : 00000000 / 00000000 / 00000000 ===Flashing [PPM2]=== Erase : Processing RM-659_022.008_241.01_default_79.92.2011.21_prd.rofs3.fpsx Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing RM-659_022.008_241.01_default_79.92.2011.21_prd.rofs3.fpsx CMT: Writing Hash CERT [SOS+ROFS3] Total writen 3 blocks TIME : Write time : 00:00:00 PPM Write done ADL: Request programm status NAND status : 00000000 / 00000000 / 00000000 ADL: Close_Session Content: 000300000000000000000000000000 ADL: Reboot Flashing done! Total flash time : 00:00:23 Reboot phone now... Reading Phone Info.... Connected phone - Nokia X7-00 Software Info: V 92_11w21 25-05-11 RM-659 (c) Nokia IMEI: 12345610654321? Ape Version: 022.008 Product code: Checking... SimLock status : SimLock is Ok Security status : Security is Ok Read Info Done! AfterFlash operations done ;D Done! Elapsed: 00:00:48 Connect phone on selected interface... Phone found! Series 60 Device detected! read info... - Ok Operating mode is OK, no need change... Reading PM from field 0 to 400 Field [1] 31 Record(s) Record 0: 10 byte(s) readed - Ok Record 1: 94 byte(s) readed - Ok Record 2: 110 byte(s) readed - Ok Record 4: 10 byte(s) readed - Ok Record 6: 110 byte(s) readed - Ok Record 7: 450 byte(s) readed - Ok Record 8: 10 byte(s) readed - Ok Record 13: 110 byte(s) readed - Ok Record 15: 30 byte(s) readed - Ok Record 16: 30 byte(s) readed - Ok Record 17: 30 byte(s) readed - Ok Record 18: 30 byte(s) readed - Ok Record 19: 30 byte(s) readed - Ok Record 22: 24 byte(s) readed - Ok Record 26: 10 byte(s) readed - Ok Record 27: 36 byte(s) readed - Ok Record 28: 110 byte(s) readed - Ok Record 29: 10 byte(s) readed - Ok Record 30: 36 byte(s) readed - Ok Record 31: 24 byte(s) readed - Ok Record 32: 216 byte(s) readed - Ok Record 33: 36 byte(s) readed - Ok Record 35: 24 byte(s) readed - Ok Record 36: 24 byte(s) readed - Ok Record 38: 216 byte(s) readed - Ok Record 39: 36 byte(s) readed - Ok Record 40: 24 byte(s) readed - Ok Record 41: 216 byte(s) readed - Ok Record 43: 36 byte(s) readed - Ok Record 44: 216 byte(s) readed - Ok Record 45: 216 byte(s) readed - Ok Field [2] 1 Record(s) Record 0: 2808 byte(s) readed - Ok Field [4] 7 Record(s) Record 1: 200 byte(s) readed - Ok Record 3: 10 byte(s) readed - Ok Record 4: 8 byte(s) readed - Ok Record 5: 8 byte(s) readed - Ok Record 6: 8 byte(s) readed - Ok Record 9: 5 byte(s) readed - Ok Record 28: 2 byte(s) readed - Ok Field [6] 1 Record(s) Record 0: 96 byte(s) readed - Ok Field [8] 8 Record(s) Record 0: 2 byte(s) readed - Ok Record 1: 16 byte(s) readed - Ok Record 2: 16 byte(s) readed - Ok Record 3: 128 byte(s) readed - Ok Record 4: 128 byte(s) readed - Ok Record 5: 8 byte(s) readed - Ok Record 8: 8 byte(s) readed - Ok Record 10: 32 byte(s) readed - Ok Field [11] 5 Record(s) Record 0: 4 byte(s) readed - Ok Record 1: 4 byte(s) readed - Ok Record 2: 4 byte(s) readed - Ok Record 3: 4 byte(s) readed - Ok Record 4: 1059 byte(s) readed - Ok Field [12] 1 Record(s) Record 0: 8 byte(s) readed - Ok Field [26] 2 Record(s) Record 0: 16 byte(s) readed - Ok Record 1: 68 byte(s) readed - Ok Field [31] 1 Record(s) Record 4: 10 byte(s) readed - Ok Field [44] 1 Record(s) Record 0: 1 byte(s) readed - Ok Field [50] 1 Record(s) Record 0: 2 byte(s) readed - Ok Field [54] 2 Record(s) Record 0: 2 byte(s) readed - Ok Record 2: 24 byte(s) readed - Ok Field [96] 2 Record(s) Record 0: 2 byte(s) readed - Ok Record 1: 20 byte(s) readed - Ok Field [117] 10 Record(s) Record 0: 4 byte(s) readed - Ok Record 1: 3 byte(s) readed - Ok Record 2: 6 byte(s) readed - Ok Record 3: 1 byte(s) readed - Ok Record 5: 10 byte(s) readed - Ok Record 6: 8 byte(s) readed - Ok Record 8: 42 byte(s) readed - Ok Record 13: 3 byte(s) readed - Ok Record 14: 3 byte(s) readed - Ok Record 16: 40 byte(s) readed - Ok Field [120] 4 Record(s) Record 0: 56 byte(s) readed - Ok Record 1: 160 byte(s) readed - Ok Record 2: 130 byte(s) readed - Ok Record 3: 112 byte(s) readed - Ok Field [153] 6 Record(s) Record 0: 68 byte(s) readed - Ok Record 1: 68 byte(s) readed - Ok Record 2: 68 byte(s) readed - Ok Record 3: 68 byte(s) readed - Ok Record 4: 68 byte(s) readed - Ok Record 5: 68 byte(s) readed - Ok Field [193] 4 Record(s) Record 2: 8 byte(s) readed - Ok Record 3: 32 byte(s) readed - Ok Record 4: 32 byte(s) readed - Ok Record 9: 64 byte(s) readed - Ok Field [217] 1 Record(s) Record 0: 32 byte(s) readed - Ok Field [239] 7 Record(s) Record 0: 2 byte(s) readed - Ok Record 1: 3817 byte(s) readed - Ok Record 2: 3817 byte(s) readed - Ok Record 3: 3817 byte(s) readed - Ok Record 4: 3817 byte(s) readed - Ok Record 5: 3817 byte(s) readed - Ok Record 6: 218 byte(s) readed - Ok Field [291] 1 Record(s) Record 0: 92 byte(s) readed - Ok Field [308] 7 Record(s) Record 0: 1 byte(s) readed - Ok Record 1: 8192 byte(s) readed - Ok Record 3: 1 byte(s) readed - Ok Record 4: 1 byte(s) readed - Ok Record 6: 1 byte(s) readed - Ok Record 7: 1 byte(s) readed - Ok Record 9: 40 byte(s) readed - Ok Field [309] 7 Record(s) Record 0: 4 byte(s) readed - Ok Record 1: 2 byte(s) readed - Ok Record 2: 12 byte(s) readed - Ok Record 3: 36 byte(s) readed - Ok Record 4: 12 byte(s) readed - Ok Record 7: 12 byte(s) readed - Ok Record 17: 12 byte(s) readed - Ok Field [313] 1 Record(s) Record 0: 800 byte(s) readed - Ok Field [322] 1 Record(s) Record 0: 1 byte(s) readed - Ok Field [327] 1 Record(s) Record 0: 2 byte(s) readed - Ok Field [329] 1 Record(s) Record 0: 8392 byte(s) readed - Ok Field [334] 1 Record(s) Record 0: 1 byte(s) readed - Ok Field [341] 3 Record(s) Record 0: 1 byte(s) readed - Ok Record 3: 4 byte(s) readed - Ok Record 4: 4512 byte(s) readed - Ok Field [354] 1 Record(s) Record 0: 8 byte(s) readed - Ok Field [356] 1 Record(s) Record 0: 2 byte(s) readed - Ok Field [360] 2 Record(s) Record 0: 1 byte(s) readed - Ok Record 1: 2 byte(s) readed - Ok Field [369] 1 Record(s) Record 0: 40 byte(s) readed - Ok Field [382] 2 Record(s) Record 0: 64 byte(s) readed - Ok Record 1: 4 byte(s) readed - Ok Field [388] 1 Record(s) Record 0: 4 byte(s) readed - Ok Field [395] 1 Record(s) Record 0: 16 byte(s) readed - Ok Saved as C:\InfinityBox\BEST\Backup\Cert\X7 RPL\RM-659 Nokia X7-00-pm.pm Done! Elapsed: 00:00:01 Backup Certificates now... Backup CRT308 data... CRT308 Backup Created SLx Simlock Data read ... ok SL3 Simlock Sign read ... ok WMDRM read ... ok Check communication with phone.... Reboot.... Connection opened successfully Waiting for communication response... [BB5 FLASH]: Bootrom Ok! ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 06D0011957A70344D5C803B7046F9F58DA450C32 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.34.0 Processing RAWLOADER... FLIC : 006800EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.34.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:02 Reopening the connection... Waiting for response: 30 Waiting for response: 29 ADL: Check mode Select ASIC [C900] PAPUBkeys : 9A17C4A57D80D29519AAEF45209AD2F5CF4AD9E9 ADL: Reading certificates... Reading NPC certificate... IMEI : 000000000000000 Reading CCC certificate... Reading HWC certificate... Reading R&D certificate... Reading VARIANT certificate... Reading PARTNERC certificate... Reading MDM_KEYS certificate... Cert Read done! ADL: Reading certificates done! :) ADL: Close_Session Content: 000300000000000000000000000000 ADL: Reboot CCC Certificate saved... HWC Certificate saved... SimLock Data saved... SimLock Key saved... WMDRM_PD Data saved... RPL saved : c:\InfinityBox\BEST\Backup\Cert\000000000000000_2nd.rpl All done, Disconnecting Elapsed: 00:00:08 Connect phone on selected interface... Phone found! Series 60 Device detected! read info... - Ok Initializing Tests... IMEI : 12345610654321? , Phone : RM-659 Nokia X7-00 Get keys... PASSED | ST_SLEEP_X_LOOP_TEST PASSED | ST_UEM_CBUS_IF_TEST PASSED | ST_EAR_DATA_LOOP_TEST PASSED | ST_SIM_CLK_LOOP_TEST PASSED | ST_SIM_LOCK_TEST PASSED | ST_SECURITY_TEST PASSED | ST_PWR_KEY_TEST PASSED | ST_CURRENT_CONS_TEST PASSED | ST_HOOKINT_TEST PASSED | ST_BTEMP_TEST PASSED | ST_KELVIN_BATVOLTAGE_TEST PASSED | ST_KELVIN_VIBRA_TEST PASSED | ST_KELVIN_CAPACITOR_TEST PASSED | ST_KELVIN_MISC_TEST PASSED | ST_KELVIN_AUDIO_TEST PASSED | ST_KELVIN_XEAR_TEST PASSED | ST_USB_CHARGING_TEST PASSED | ST_DIGIMIC_TEST PASSED | ST_HEADSET_AMPLIFIER_TEST PASSED | ST_LED_CONTROLLER_TEST PASSED | ST_AUDIO_PLL_TEST PASSED | ST_RAM_IF_TEST PASSED | ST_CDSP_SLEEPCLOCK_FREQ_TEST PASSED | ST_CDSP_RF_BB_IF_TEST PASSED | ST_CDSP_STROBE_TEST PASSED | ST_CDSP_DIGI_RXTX_IF_TEST PASSED | ST_CDSP_RF_SUPPLY_TEST PASSED | ST_CDSP_PA_ID_PIN_TEST NOT RUN | ST_CDSP_WCDMA_TX_POWER_TEST PASSED | ST_KEYBOARD_STUCK_TEST PASSED | ST_LPRF_IF_TEST PASSED | ST_CAMERA_IF_TEST PASSED | ST_CAMERA_ACCELERATOR_TEST PASSED | ST_LED_FLASH_TEST PASSED | ST_LPRF_AUDIO_LINES_TEST PASSED | ST_MAIN_LCD_IF_TEST PASSED | ST_TOUCH_TEST PASSED | ST_TOUCH_IF_TEST PASSED | ST_BT_WAKEUP_TEST PASSED | ST_WLAN_TEST PASSED | ST_ACCEL_IF_TEST PASSED | ST_VIBRA_TEST NOT RUN | ST_USB_LOOP_TEST PASSED | ST_USB_CHARGER_TEST PASSED | ST_LED_FLASH_IF_TEST PASSED | ST_PROXIMITY_TEST SelfTests end Done! Elapsed: 00:00:40 Phone disconected! |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Вложений: 1
Цитата:
Теперь у нас есть все критически важные DATA для восстановления телефона после полного стирания. Сделайте следующее: - Сотрите телефон полностью - Запишите SW соответствующего железу RM-659 После этого телефон должен полностью включиться и пару минут работать с IMEI 123456... Если включился, то - Запишите приложенный X7_35789904019401_Rep_RPL |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
Добавил расширение и залил на прежнее место. |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
После стирания я его прошил но он не заходит в режим Local mode
вот лог:Connect phone on selected interface...
User ACCEPTED FULL ERASE Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- Connection opened successfully Waiting for communication response... [BB5 FLASH]: Bootrom Ok! ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 06D0011957A70344D5C803B7046F9F58DA450C32 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.34.0 Processing RAWLOADER... FLIC : 006800EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.34.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:02 Reopening the connection... Waiting for response: 30 Waiting for response: 29 ADL: Check mode Select ASIC [C900] PAPUBkeys : 9A17C4A57D80D29519AAEF45209AD2F5CF4AD9E9 ADL: Preparing for erase... Full Erase started... Asic : CMT , Sub : NAND Erase Area 0x00000000-0x3FFFFFFF Erasing Ok , [0F] Erase done , time : 00:00:04 ADL: Erase done ADL: Close_Session Content: 000205000000000000FFFF00000000 ADL: Reboot Phone disconected! Connect phone on selected interface... Core version : 1.30 Rev : 1.1 Selected FlashSettings : Manual Check FlashFiles, Please, wait... Files Set for Flashing : MCU : RM-659_022.008_79.92_prd.core.fpsx PPM : RM-659_022.008_31.01_NAM_79.92_prd.rofs2.fpsx PPM2 : RM-659_022.008_241.01_default_79.92.2011.21_prd.rofs3.fpsx Flashing phone now... Check files done... -> SWversion check skipped : Dead mode selected Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- Connection opened successfully Waiting for communication response... [BB5 FLASH]: Bootrom Ok! ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 06D0011957A70344D5C803B7046F9F58DA450C32 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.34.0 Processing RAWLOADER... FLIC : 006800EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.34.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:02 Reopening the connection... Waiting for response: 30 Waiting for response: 29 ADL: Check mode Select ASIC [C900] PAPUBkeys : blank (Erased or HW failure) ADL: phone is in flash mode Backup enabled, will read all certificates... Reading NPC certificate... Reading CCC certificate... Reading HWC certificate... Reading R&D certificate... Reading VARIANT certificate... Reading PARTNERC certificate... Reading MDM_KEYS certificate... - > No any CRT data (MCU damaged/CERT erased), skip saving ===Flashing [MCU]=== Erase : Processing RM-659_022.008_79.92_prd.core.fpsx Partitioning.... Partitioning Ok... Erasing.... Erasing Ok... TIME : Erase time : 00:00:02 Write : Processing RM-659_022.008_79.92_prd.core.fpsx CMT: Writing Hash CERT [ADA] CMT: Writing Hash CERT [KEYS] CMT: Writing Hash CERT [PRIMAPP] CMT: Writing Hash CERT [RAP3NAND] CMT: Writing Hash CERT [SOS+PMML] CMT: Writing Hash CERT [PASUBTOC] CMT: Writing Hash CERT [PAPUBKEYS] CMT: Writing Hash CERT [GENIO_INIT] CMT: Writing Hash CERT [SOS*UPDAPP] CMT: Writing Hash CERT [SOS*DSP0] CMT: Writing Hash CERT [LDSP] CMT: Writing Hash CERT [SOS*ISASW] CMT: Writing Hash CERT [SOS+CORE] CMT: Writing Hash CERT [SOS+ROFS1] Total writen 505 blocks TIME : Write time : 00:00:15 MCU Write done ADL: Request programm status NAND status : 00000000 / 00000000 / 00000000 ===Flashing [PPM]=== Erase : Processing RM-659_022.008_31.01_NAM_79.92_prd.rofs2.fpsx Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing RM-659_022.008_31.01_NAM_79.92_prd.rofs2.fpsx CMT: Writing Hash CERT [SOS+ROFS2] Total writen 186 blocks TIME : Write time : 00:00:05 PPM Write done ADL: Request programm status NAND status : 00000000 / 00000000 / 00000000 ===Flashing [PPM2]=== Erase : Processing RM-659_022.008_241.01_default_79.92.2011.21_prd.rofs3.fpsx Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing RM-659_022.008_241.01_default_79.92.2011.21_prd.rofs3.fpsx CMT: Writing Hash CERT [SOS+ROFS3] Total writen 3 blocks TIME : Write time : 00:00:00 PPM Write done ADL: Request programm status NAND status : 00000000 / 00000000 / 00000000 ADL: Close_Session Content: 000300000000000000000000000000 ADL: Reboot Flashing done! Total flash time : 00:00:23 Reboot phone now... - > AfterFlash Failed! :( Reason : Downgrade try or HW Error Anyway - try reinsert battery and PowerUp phone manualy Connect phone on selected interface... Done! Elapsed: 00:02:21 Connect phone on selected interface... |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
- неполностью стёрся - прошивка не соответствует железу (не тот RM) - файлы прошивки не все или битые Попробуйте найти и отдельно записать файл ENO для этой модели. |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Такая же проблема...Сохранил бэкап RPL и PM...Изначально хотели русифицировать и прошить как RM-707. Сделали полное стирание он не шьется как 707...скачали родную прошивку....после прошивки не входит в Локал...
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
У вас нет его?
Что он делает? этот ENO... |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
А вы попробуйте версию по выше записать RM-707_025.007_04.01
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
707 не записывет вообше..ругется....пробывали 111 версию
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Подскажите ENO писать после стирания полного...или после флеширования родной версией?
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
В принципе не важно.
Но наверное лучше так: - стирание - ENO - SW |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Спасибо за совет! Завтра попробуем...Отпишусь по результатам. Это должно помочь, ведь так?
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Всё получилось...Спасибо за помощь!
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Павел не обязательно будет local. Данный аппарат не полностью стирается atf и best. В итоге после прошивки anna телефон включается но не входит в local. При этом серты битые и телефон перегружается. Принудительно бокасами и резистором в local и test не переводиться. После залития только npc в local тоже не входит. После Belle local и test есть. Но отсутствует cmla. В итоге проблема решается только проливкой заводского rpl.
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
такая же проблема- после понижения прошивки не включается ни с анна ни с бэль, все бэкапы есть, но не помогают.
стирание:Connect phone on selected interface...
Phone found! Series 60 Device detected! read info... - Ok User ACCEPTED FULL ERASE Connection opened successfully Waiting for communication response... BootRom : 1st boot ok ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 24300207B9D8034460936F39DBDF76565C606B35 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0 Processing RAWLOADER... FLIC : 006000EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:03 Seek file for this phone.... - > Backup for phone found and it is Ok :) Reopening the connection... Waiting for response: 30 ADL: Check mode Select ASIC [C900] PAPUBkeys : A777258432D3E9101D6160DBAC2702FCC602E752 Reading NPC certificate... IMEI : 356257049694397 Reading CCC certificate... Reading HWC certificate... Reading R&D certificate... Reading VARIANT certificate... Reading PARTNERC certificate... Reading MDM_KEYS certificate... Cert Read done! NPC Certificate saved... CCC Certificate saved... HWC Certificate saved... RPL saved : c:\InfinityBox\BEST\Backup\Cert\356257049694397_CRT_2nd.rpl ADL: Preparing for erase... Full Erase started... Asic : CMT , Sub : NAND Erase Area 0x00000000-0x3FFFFFFF Erasing Ok , [0F] Erase done , time : 00:00:03 ADL: Erase done ADL: Close_Session Content: 000205000000000000FFFF00000000 ADL: Reboot Phone disconected! Connect phone on selected interface... прошивка sw 25:Core : v1.53 , FlashEngine : v1.9
Selected FlashSettings : Cold Flash Check FlashFiles, Please, wait... Files Set for Flashing : MCU : RM-707_025.007_79.92_prd.core.fpsx PPM : RM-707_025.007_04.01_Russian_79.92_prd.rofs2.fpsx PPM2 : RM-707_025.007_00.01_79.92_prd.rofs3.fpsx CNT : RM-707_025.007_U01.01_79.92.uda.fpsx APE : rm707_APEONLYENO_11w44v0.003.fpsx Flashing phone now... Check files done... -> SWversion check skipped : Dead mode selected Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- Connection opened successfully Waiting for communication response... BootRom : 1st boot ok ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 24300207B9D8034460936F39DBDF76565C606B35 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0 Processing RAWLOADER... FLIC : 006000EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:02 Reopening the connection... Waiting for response: 30 Waiting for response: 29 ADL: Check mode Select ASIC [C900] PAPUBkeys : blank (Erased or HW failure) ADL: phone is in flash mode ===Flashing [MCU]=== Erase : Processing RM-707_025.007_79.92_prd.core.fpsx Partitioning.... Partitioning Ok... Erasing.... Erasing Ok... TIME : Erase time : 00:00:02 Write : Processing RM-707_025.007_79.92_prd.core.fpsx CMT: Writing Hash CERT [ADA] CMT: Writing Hash CERT [KEYS] CMT: Writing Hash CERT [PRIMAPP] CMT: Writing Hash CERT [RAP3NAND] CMT: Writing Hash CERT [SOS+PMML] CMT: Writing Hash CERT [PASUBTOC] CMT: Writing Hash CERT [PAPUBKEYS] CMT: Writing Hash CERT [GENIO_INIT] CMT: Writing Hash CERT [SOS*UPDAPP] CMT: Writing Hash CERT [SOS*DSP0] CMT: Writing Hash CERT [LDSP] CMT: Writing Hash CERT [SOS*ISASW] CMT: Writing Hash CERT [SOS+CORE] CMT: Writing Hash CERT [SOS+ROFS1] Total writen 504 blocks TIME : Write time : 00:00:18 MCU Write done ADL: Request programm status NAND status : 00000002 / 00000002 / 00000000 ===Flashing [PPM]=== Erase : Processing RM-707_025.007_04.01_Russian_79.92_prd.rofs2.fpsx Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing RM-707_025.007_04.01_Russian_79.92_prd.rofs2.fpsx CMT: Writing Hash CERT [SOS+ROFS2] Total writen 194 blocks TIME : Write time : 00:00:07 PPM Write done ADL: Request programm status NAND status : 00000002 / 00000002 / 00000000 ===Flashing [PPM2]=== Erase : Processing RM-707_025.007_00.01_79.92_prd.rofs3.fpsx Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing RM-707_025.007_00.01_79.92_prd.rofs3.fpsx CMT: Writing Hash CERT [SOS+ROFS3] Total writen 2 blocks TIME : Write time : 00:00:00 PPM Write done ADL: Request programm status NAND status : 00000002 / 00000002 / 00000000 ===Flashing [CNT]=== Erase : Processing RM-707_025.007_U01.01_79.92.uda.fpsx Erasing.... Erasing Ok... TIME : Erase time : 00:00:01 Write : Processing RM-707_025.007_U01.01_79.92.uda.fpsx Total writen 525 blocks TIME : Write time : 00:00:23 CNT Write done ADL: Request programm status NAND status : 00000002 / 00000002 / 00000000 ===Flashing [APE]=== Erase : Processing rm707_APEONLYENO_11w44v0.003.fpsx Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing rm707_APEONLYENO_11w44v0.003.fpsx CMT: Writing Hash CERT [SOS*ENO] Total writen 20 blocks TIME : Write time : 00:00:00 APE Write done ADL: Request programm status NAND status : 00000002 / 00000002 / 00000000 ADL: Close_Session Content: 000300000000020000000200000000 ADL: Reboot Flashing done! Total flash time : 00:00:55 Reboot phone now... local mode нет запись rpl:Dead Mode is Selected
Waiting for USB device... --- Insert cable and charger or press phone's power button! --- Connection opened successfully Waiting for communication response... BootRom : 1st boot ok ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 24300207B9D8034460936F39DBDF76565C606B35 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0 Processing RAWLOADER... FLIC : 006000EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:03 Seek file for this phone.... ----------------------------- - > RPL file found for this phone! - > NPC Found in : 356257049694397.rpl Check RPL file... NPC Data found! (CMT) CCC Data found! (CMT) HWC Data found! (CMT) SimLock Data found! SimLock key found! WMDRM key found! ----------------------------- Reopening the connection... Waiting for response: 30 ADL: Check mode Select ASIC [C900] PAPUBkeys : A777258432D3E9101D6160DBAC2702FCC602E752 ADL: Preparing for write certificates... Erase NPC... Ok Writing NPC... Ok Erase CCC... Ok Writing CCC... Ok Erase HWC... Ok Writing HWC... Ok ADL: Writing Flash certs done! :) ADL: Close_Session Content: 000300000000020000000200000000 ADL: Reboot Wait, reconneting... - > Phone not found... :( - > CertWrite failed : phone was not bootup - > Connection/SW/HW problem, try bootup manually - > If phone bootup Ok - write only flex keys Connect phone on selected interface... |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
ENO записывали? |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
Скрытый текстSelected FlashSettings : Manual
Check FlashFiles, Please, wait... Files Set for Flashing : MCU : rm707_APEONLYENO_11w44v0.003.fpsx Flashing phone now... Check files done... -> SWversion check skipped : Dead mode selected Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- Connection opened successfully Waiting for communication response... BootRom : 1st boot ok ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 24300207B9D8034460936F39DBDF76565C606B35 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0 Processing RAWLOADER... FLIC : 006000EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:03 Reopening the connection... Waiting for response: 30 ADL: Check mode Select ASIC [C900] PAPUBkeys : A777258432D3E9101D6160DBAC2702FCC602E752 ADL: phone is in flash mode ===Flashing [MCU]=== Erase : Processing rm707_APEONLYENO_11w44v0.003.fpsx Erasing.... Erasing Ok... TIME : Erase time : 00:00:00 Write : Processing rm707_APEONLYENO_11w44v0.003.fpsx CMT: Writing Hash CERT [SOS*ENO] Total writen 20 blocks TIME : Write time : 00:00:01 MCU Write done ADL: Request programm status NAND status : 00000002 / 00000002 / 00000000 ADL: Close_Session Content: 000300000000020000000200000000 ADL: Reboot Flashing done! Total flash time : 00:00:01 Reboot phone now... - > AfterFlash Failed! :( Reason : Downgrade try or HW Error Anyway - try reinsert battery and PowerUp phone manualy Connect phone on selected interface... Done! Elapsed: 00:02:02 Connect phone on selected interface... с файлом X7_ENOAPE_wk2012_0125.fpx_cry эффект тот же |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
Дим@ а в ваших бэкапах есть CMLA_KEY_DATA ? |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Вложений: 3
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Вложений: 1
Цитата:
Попробуйте так: -- полное стирание -- запись ENO от версии anna -- запись соответствующей ENO anna версии из полного Nokia SW Installer по INI будет ли включаться с IMEI 123456... ? -- запись RM-707_356257049694397_Repair_RPL |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Цитата:
|
Re: Nokia X7 RM-659 не включается после прошивки RM-707
Попробуйте сначала вообще без ENO.
Если не получится, то пробуйте найти ENO для anna версии. Если не найдёте, то пробуйте писать ENO X7_ENOAPE_wk2012_0125.fpx_cry Если не даст результата, то пишите от 111 версии. По-идее ENO не должны принципиально различаться. P.S. Раз вы уже его стирали, включается ли он после стирания и записи только SW с IMEI 123456... ? |
Re: Nokia X7 RM-659 не включается после прошивки RM-707
после стирания и прошивки SW 025.007 local modе не появился, но тело включается, стоит записать в него rpl локала опять-таки нет и переваливается на nokia
Скрытый текстElapsed: 00:03:02
Connect phone on selected interface... Will Write RPL keys now... Check RPL file... NPC Data found! (CMT) CCC Data found! (CMT) HWC Data found! (CMT) SimLock Data found! SimLock key found! CMLA key found! WMDRM key found! Dead Mode is Selected Waiting for USB device... --- Insert cable and charger or press phone's power button! --- Connection opened successfully Waiting for communication response... BootRom : 1st boot ok ASIC ID: 000000030000022600010007600C192102031104 CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB EM0 ID: 00001040 EM1 ID: 00001030 PUBLIC ID: 24300207B9D8034460936F39DBDF76565C606B35 ASIC MODE ID: 00 ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B ROM ID: E693EF0DAC22615B Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0 Processing RAWLOADER... FLIC : 006000EC Req : XSR 1.6 Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0 Processing PASUBTOC ... Processing ALG ... Boot Done! :) TIME : Boot time : 00:00:02 Reopening the connection... Waiting for response: 30 Waiting for response: 29 ADL: Check mode Select ASIC [C900] PAPUBkeys : A777258432D3E9101D6160DBAC2702FCC602E752 ADL: Preparing for write certificates... Erase NPC... Ok Writing NPC... Ok Erase CCC... Ok Writing CCC... Ok Erase HWC... Ok Writing HWC... Ok ADL: Writing Flash certs done! :) ADL: Close_Session Content: 000300000000020000000200000000 ADL: Reboot Wait, reconneting... Phone not found... :( CertWrite failed : phone was not bootup Connection/SW/HW problem, try bootup manually If phone bootup Ok - write only flex keys Phone disconected! Connect phone on selected interface... |
| Текущее время: 17:30. Часовой пояс GMT +3. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd. Перевод: zCarot
© 2007—2022 www.UO5OQ.com