Перестал прошивать BB5

[Kvest]

Лог:

RM170p_0736.C01, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: Single Line 8Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.30.0, Algo: BB5
Flashbus Write baud set to 51Kbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC220800008D21, Samsung, NOR
FlashChip[0,CMT]: 0x00EC003000000121, Samsung, ONENAND
Requested Algorithm: BB5 ALGORITHM (CMT)
FlashContent[0,CMT]: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: Single Line 8Bit
Processing Flash Image Failed -> Not found required Algorithm
Failed to Process all Image files -> Failed to process RM170p_0736.C01

Не смог прошить Е50

[Kvest]

Лог:

RM170p_0736.C01, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 51Kbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x00EC220800008D21, Samsung, NOR
FlashChip[0,CMT]: 0x00EC003000000121, Samsung, ONENAND
Requested Algorithm: BB5 ALGORITHM (CMT)
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC2208 (Samsung), Size: 32MBytes, VPP: 9V
FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 378E6A71B6975E4F03868F793B3BCC7502219779
Flashbus Write baud set to 5.0Mbits
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00380000-0x01F7FFFF, NOR
EraseArea[0,CMT]: 0x00000400-0x000006BF, NOR
EraseArea[0,CMT]: 0x000006C0-0x0000FFFF, NOR
EraseArea[0,CMT]: 0x00010000-0x000105FF, NOR
EraseArea[0,CMT]: 0x00010600-0x00010FFF, NOR
EraseArea[0,CMT]: 0x00011000-0x00011FFF, NOR
EraseArea[0,CMT]: 0x00012000-0x00013FFF, NOR
EraseArea[0,CMT]: 0x00020000-0x0013FFFF, NOR
EraseArea[0,CMT]: 0x00140000-0x0032FFFF, NOR
EraseArea[0,CMT]: 0x00330000-0x0033FFFF, NOR
EraseArea[0,CMT]: 0x00340000-0x0037FBFF, NOR
EraseArea[0,CMT]: 0x0037FC00-0x0037FFFF, NOR
EraseArea[0,CMT]: 0x01FA0000-0x01FDFFFF, NOR
EraseArea[0,CMT]: 0x00000000-0x012FFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 82.415s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT MCUSW Certificate...
Block Write Failed -> Failed to write CMT cert data (3), Programming Status Error
Processing Flash Image Failed -> Failed to write all blocks
Failed to Process all Image files -> Failed to process RM170p_0736.C01

в чем грабли? мхбокс нормально шьет а этот тупой циклоп тупит