|
|
Cyclone Box Вопросы по работе программатора Cyclone Box |
|
Опции темы | Поиск в этой теме |
03.07.2012, 17:03 | #1 |
Member
Регистрация: 07.04.2012
Сообщений: 37
Вес репутации: 17 |
Перестал прошивать BB5
Лог:RM170p_0736.C01, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: Single Line 8Bit RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.1.30.0, Algo: BB5 Flashbus Write baud set to 51Kbits Flashbus Read baud set to 98Kbits Using OLD BB5 FLASHING PROTOCOL If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x00EC220800008D21, Samsung, NOR FlashChip[0,CMT]: 0x00EC003000000121, Samsung, ONENAND Requested Algorithm: BB5 ALGORITHM (CMT) FlashContent[0,CMT]: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF, NOR FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit Searching for BootCode: Single Line 8Bit Processing Flash Image Failed -> Not found required Algorithm Failed to Process all Image files -> Failed to process RM170p_0736.C01 Не смог прошить Е50 |
03.07.2012, 17:38 | #2 |
Member
Регистрация: 07.04.2012
Сообщений: 37
Вес репутации: 17 |
Re: Перестал прошивать BB5
Лог:RM170p_0736.C01, Type: Flash Image, Algo: BB5, BB5 ALGORITHM
Searching for BootCode: DualLine 32Bit RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5 Flashbus Write baud set to 51Kbits Flashbus Read baud set to 98Kbits Using OLD BB5 FLASHING PROTOCOL If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x00EC220800008D21, Samsung, NOR FlashChip[0,CMT]: 0x00EC003000000121, Samsung, ONENAND Requested Algorithm: BB5 ALGORITHM (CMT) FlashContent[0,CMT]: 00000000000000000000000000000000, NOR FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit Searching for BootCode: DualLine 32Bit FlashChip 0x00EC2208 (Samsung), Size: 32MBytes, VPP: 9V FlashChip 0x00EC0030 (Samsung), Size: 128MBytes, VPP: Not Supported RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM Flashbus Write baud set to 2.0Mbits Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: 378E6A71B6975E4F03868F793B3BCC7502219779 Flashbus Write baud set to 5.0Mbits Partitioning... Partitioning OK Started group flash erase EraseArea[0,CMT]: 0x00380000-0x01F7FFFF, NOR EraseArea[0,CMT]: 0x00000400-0x000006BF, NOR EraseArea[0,CMT]: 0x000006C0-0x0000FFFF, NOR EraseArea[0,CMT]: 0x00010000-0x000105FF, NOR EraseArea[0,CMT]: 0x00010600-0x00010FFF, NOR EraseArea[0,CMT]: 0x00011000-0x00011FFF, NOR EraseArea[0,CMT]: 0x00012000-0x00013FFF, NOR EraseArea[0,CMT]: 0x00020000-0x0013FFFF, NOR EraseArea[0,CMT]: 0x00140000-0x0032FFFF, NOR EraseArea[0,CMT]: 0x00330000-0x0033FFFF, NOR EraseArea[0,CMT]: 0x00340000-0x0037FBFF, NOR EraseArea[0,CMT]: 0x0037FC00-0x0037FFFF, NOR EraseArea[0,CMT]: 0x01FA0000-0x01FDFFFF, NOR EraseArea[0,CMT]: 0x00000000-0x012FFFFF, ONENAND Waiting 320s for erasure finish... Erase taken 82.415s Writing all blocks... Initializing TurboCache... TurboCache Loaded! Writing CMT MCUSW Certificate... Block Write Failed -> Failed to write CMT cert data (3), Programming Status Error Processing Flash Image Failed -> Failed to write all blocks Failed to Process all Image files -> Failed to process RM170p_0736.C01 в чем грабли? мхбокс нормально шьет а этот тупой циклоп тупит |