Zylo залочен.Разлочить бы.

[Kvest]

Как и чем отвязать от сети?

[UO5OQ]

Как и чем отвязать от сети?
Пробовали SETool ?

[Kvest]

Нет еще. Там кредиты вроде надо, 6 штук за отвязку от сети. А если Омниусом отвязать за 10 зеленых?

[UO5OQ]

Нет еще. Там кредиты вроде надо, 6 штук за отвязку от сети. А если Омниусом отвязать за 10 зеленых?
6 кредитов это Factory unlock, когда работает Remote dongle. А он не работает сейчас.

Вот посмотрите: Список ПОТРЕБЛЕНИЯ КРЕДИТОВ и поддерживаемые модели SETool (http://www.uo5oq.com/forum/showthread.php?t=350)

Возможности Omnius можно посмотреть тут: http://www.omnius-server.com/phone?id=103

[Kvest]

User code reset только написано

[UO5OQ]

User code reset только написано
SETool сделает раскодировку от оператора за 3 кредита и без использования Remote Dongle.
Вот инструкция от автора the_laser

UNLOCKING OF A2 PHONES

CID 49,51,52,53

standalone usercode reset
1. select proper model
2. on settings, check "signed mode"
3. back to semc a2 tab, press unlock


CID 49,51,52,53

standalone full reset-based unlock

1. select proper model
2. select needed domain (leave "current" for no change)
3. on settings, check "signed mode","use alternative security bypass"
4. back to semc a2 tab, press unlock

that method can fix damaged SCRC and fixing SEMCBOOT automatically.
that is preferred method for such phones.

server-based full signature unlock

1. select proper model
2. on settings, check "signed mode","do full unlock instead usercode reset",fill login details
3. back to semc a2 tab, press unlock

that method can not fix SCRC.

CID 80,81

server-based full signature unlock

1. select proper model
2. on settings, check "signed mode","do full unlock instead usercode reset",fill login details
3. back to semc a2 tab, press unlock

that method can not fix SCRC.

if s1 signature server offline, you can not use quick (without modem drivers) unlock.
instead, you should :

1.
select proper model
2.
on settings, check
"signed mode",
"do full unlock instead usercode reset",
"disable flash mode activation for semc a2 phones",
fill login details
3.
back to semc a2 tab, press unlock
4.
when prompted, install phone modem drivers
(they can be found in drivers\Modem_Drivers or will be automatically installed if you install semc pc suite)
5.
when you will get message "unlock done" - do not remove cable or battery,
wait until phone automatically power on, otherwise you will get 5 locks and need to repeat procedure.

you can not unlock last SEMC A2 phone ( j108 ) with CSCA method, use special bypass (http://support.setool.net/showthread.php?10-HOW-TO-WORK-WITH-A2-BASED-PHONES&p=83068&viewfull=1#post83068) mode.
you MUST flash r7cXXX firmware version to be able unlock w20 phone with CSCA method.

CID 26,54,60,185,186

standalone full unlock

1. select proper model
2. on settings, check "signed mode"
3. back to semc a2 tab, press unlock

that method can fix SCRC.
that is preferred method to unlock such phones.