|
Nokia N9 RM-696 не прошивается
Телефон принесли на ремонт по причине того что он сильно зависал. Перед прошивкой проверил на наличие вирусов, нашел 2 трояна. Сделал Wipe не помогло. Начал прошивать туже версию Что была в теле, не удалось, потом попробовал 40-ю, тоже не прошился. Пробовал разные версии скачивал с помощью NaviFirm. Прошивка производилась программаторами BEST, Phoenix, Flasher, при прошивке все они кричат что понижение недопустимо. Считывал инфо с помощью беста, там 40-я версия прошивки (изначально была 30-я), делал попытки 30-x, 40-x версий, в т.ч. со своим продукт кодом. Без изменений..
Вот лог BEST SW_30.2012.07-1: Скрытый текстcard found: S/N 44XX:XXXX
registered to: ruis Connect phone on selected interface... Check : Processing DFL61_HARMATTAN_30.2012.07-1_PR_LEGACY_001-OEM1-958_ARM.bin ========== FW APE version : 30.2012.07-1 FW CMT version : 9.2.2011.50 FW PRx release : PR_1.2 FW Region info : EUROPE [1] , America (Latin , South), South Africa FW Region ver : 001 KERNEL version : 2.6.32-20115101+0m7 ========== Check : File Is Ok ! Check : Processing DFL61_HARMATTAN_30.2012.07-1.EURASIA_EMMC_EURASIA.bin ========== eMMC version : DFL61_HARMATTAN_30.2012.07-1.EURASIA ========== Check : File Is Ok ! Core : v1.48 , FlashEngine : v2.00 Insert cable in to powered OFF phone! (Ignore if phone Connected) Waiting for NOLO... Connect in NOLO mode Ok! Phone Info : Type : RM-696 , HWRev : 1603 NOLO : 01/06/23 SWVer: DFL61_HARMATTAN_40.2012.21-3.339.2_PR_339 Device mode : Production mode Read info Ok Processing APE Boot... File : DFL61_HARMATTAN_30.2012.07-1_PR_LEGACY_001-OEM1-958_ARM.bin Processing : ape-algo APE Algorithm boot Ok Reopening the connection... RFS mode init Ok Device : RM-696 HW build : 1603 Bat.level : 24 SW release : (empty) Protocol : 108 UPDAPP ver : 1.7.2 Upd/Dev PT : 3 , 3 FL_images : cert-sw,xloader,secondary,rootfs,kernel,moslo,config,mmc,tar,cmt-2nd,cmt-algo,cmt-mcusw Last errors : bb5_rdc_cert_read failed Code Match Ok HW match Ok RFS : Performing SWAP WIPE... Starting Wipe... Bat.level : 24 Battery voltage is enough, starting wipe... Formatting... Can take up to 15-50 minutes, wait until process complete Do not disconnect phone, until done! RFS : Swap format Ok RFS : No any errors RFS Set : Host Protocol set to 108 RFS Set : CMT Verify On RFS Set : Perform RFS On RFS Set : eMMC preserve On ---Processing MCU image--- Processing File : DFL61_HARMATTAN_30.2012.07-1_PR_LEGACY_001-OEM1-958_ARM.bin RFS : Sending config for [cert-sw] -> Ver T : RM-696 -> Ver H : 1507 , 1508 , 1509 , 1510 , 1601 , 1602 , 1603 , 1604 , 1605 , 1701 , 1702 , 1703 , 1704 , 1705 , 1801 , 1802 , 1803 , 1804 , 1805 RFS : Init pipe 00 RFS : Flashing... RFS : Finalizing... cert-sw Flash done RFS : ERROR_SECURITY! Seems as DOWNGRADE TRY! Receiving error list... Last Errors : bb5_rdc_cert_read failed Progress bar initialization failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed Downgrade disallowed (1341314349) [Pipe 0] Finishing in error state with status 10 Flashing failed More info in Last Error Log Elapsed: 00:15:54 И еще лог BEST SW_40.2012.21-3.339.2 Скрытый текстConnect phone on selected interface... Check : Processing DFL61_HARMATTAN_40.2012.21-3.339.2_PR_LEGACY_339_ARM_RM-696_PRD_signed.bin ========== FW APE version : 40.2012.21-3.339.2 FW CMT version : 9.2.2011.51 FW PRx release : PR_1.3 FW Region info : BRANDED TO CARRIER FW Region ver : 339 KERNEL version : 2.6.32-20121301+0m8 ========== Check : File Is Ok ! Core : v1.48 , FlashEngine : v2.00 Insert cable in to powered OFF phone! (Ignore if phone Connected) Waiting for NOLO... Connect in NOLO mode Ok! Phone Info : Type : RM-696 , HWRev : 1603 NOLO : 01/06/23 SWVer: DFL61_HARMATTAN_40.2012.21-3.339.2_PR_339 Device mode : Production mode Read info Ok Processing APE Boot... File : DFL61_HARMATTAN_40.2012.21-3.339.2_PR_LEGACY_339_ARM_RM-696_PRD_signed.bin Processing : ape-algo APE Algorithm boot Ok Reopening the connection... RFS mode init Ok Device : RM-696 HW build : 1603 Bat.level : 5 SW release : (empty) Protocol : 108 UPDAPP ver : 1.7.2 Upd/Dev PT : 3 , 3 FL_images : cert-sw,xloader,secondary,rootfs,kernel,moslo,config,mmc,tar,cmt-2nd,cmt-algo,cmt-mcusw Last errors : bb5_rdc_cert_read failed Code Match Ok HW match Ok Init : 0009 RFS Set : Host Protocol set to 108 RFS Set : CMT Verify On RFS Set : Perform RFS On RFS Set : eMMC preserve On ---Processing MCU image--- Processing File : DFL61_HARMATTAN_40.2012.21-3.339.2_PR_LEGACY_339_ARM_RM-696_PRD_signed.bin RFS : Sending config for [cert-sw] -> Ver T : RM-696 -> Ver H : 1507 , 1508 , 1509 , 1510 , 1601 , 1602 , 1603 , 1604 , 1605 , 1701 , 1702 , 1703 , 1704 , 1705 , 1801 , 1802 , 1803 , 1804 , 1805 RFS : Init pipe 00 RFS : Flashing... RFS : ERROR_PIPE_00_LEN_SET FAILED , 0x07 , 0 Receiving error list... Last errors : Battery level below 10% (current: 5%) bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed No pipe 0 found for PREPARE_DATA_BLOCK_REQ Лог FLASHER'а Скрытый текстC:\meego\Flasher>flasher -F DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_001-OEM1-958_
ARM.bin -f flasher 3.12.1 (Oct 6 2011) Harmattan WARNING: This tool is intended for professional use only. Using it may result in permanently damaging your device or losing the warranty. Suitable USB interface (bootloader/phonet) not found, waiting... Found device RM-696, hardware revision 1603 NOLO version 2.3.6 Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3.339.2_PR_339 Sending ape-algo image (7096 kB)... 100% (7096 of 7096 kB, avg. 20689 kB/s) Suitable USB interface (phonet) not found, waiting... Ping attempt 1 (250 ms) Server application: 1.7.2 Found product RM-696 rev. 1603 Server implements softupd protocol version 1.8 Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001 Image moslo not present Image mmc not present Image tar skipped Image config skipped Battery level 19 %, continuing. image [state progress transfer flash speed] --------------------------------------------------------------------- [_] cert-sw [init 0 % 0 / 0 kB NA ] [ ] cmt-2nd [pending 0 % 0 / 0 kB NA ] [ ] cmt-algo [pending 0 % 0 / 0 kB NA ] [ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ] [ ] xloader [pending 0 % 0 / 0 kB NA ] [ ] secondary [pending 0 % 0 / 0 kB NA ] [ ] kernel [pending 0 % 0 / 0 kB NA ] [ ] rootfs [pending 0 % 0 / 0 kB NA ] ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 10: Security failure image [state progress transfer flash speed] --------------------------------------------------------------------- [f] cert-sw [init 0 % 1 / 1 kB NA ] [ ] cmt-2nd [pending 0 % 0 / 0 kB NA ] [ ] cmt-algo [pending 0 % 0 / 0 kB NA ] [ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ] [ ] xloader [pending 0 % 0 / 0 kB NA ] [ ] secondary [pending 0 % 0 / 0 kB NA ] [ ] kernel [pending 0 % 0 / 0 kB NA ] [ ] rootfs [pending 0 % 0 / 0 kB NA ] Fetching error list: ======================================== bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed Downgrade disallowed (1341314349) [Pipe 0] Finishing in error state with status 10 ======================================== ERROR: Failed to flash images C:\meego\Flasher> |
Re: Nokia N9 RM-696 не прошивается
Еще раз внимательно прочел логи. Кажется дело в сертификатах. Может кто-нибудь сталкивался с такой проблемой. Если в этом телефоне отсутствуют сертификаты он может не прошиваться нормально?
|
Re: Nokia N9 RM-696 не прошивается
Цитата:
|
| Текущее время: 18:57. Часовой пояс GMT +3. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd. Перевод: zCarot
© 2007—2022 www.UO5OQ.com