Скрытый текст

ruis · 16.08.2012, 21:39

Телефон принесли на ремонт по причине того что он сильно зависал. Перед прошивкой проверил на наличие вирусов, нашел 2 трояна. Сделал Wipe не помогло. Начал прошивать туже версию Что была в теле, не удалось, потом попробовал 40-ю, тоже не прошился. Пробовал разные версии скачивал с помощью NaviFirm. Прошивка производилась программаторами BEST, Phoenix, Flasher, при прошивке все они кричат что понижение недопустимо. Считывал инфо с помощью беста, там 40-я версия прошивки (изначально была 30-я), делал попытки 30-x, 40-x версий, в т.ч. со своим продукт кодом. Без изменений..

Вот лог BEST SW_30.2012.07-1:

Скрытый текст

card found: S/N 44XX:XXXX
registered to: ruis

Connect phone on selected interface...

Check : Processing DFL61_HARMATTAN_30.2012.07-1_PR_LEGACY_001-OEM1-958_ARM.bin
==========
FW APE version : 30.2012.07-1
FW CMT version : 9.2.2011.50
FW PRx release : PR_1.2
FW Region info : EUROPE [1] , America (Latin , South), South Africa
FW Region ver : 001
KERNEL version : 2.6.32-20115101+0m7
==========
Check : File Is Ok !

Check : Processing DFL61_HARMATTAN_30.2012.07-1.EURASIA_EMMC_EURASIA.bin
==========
eMMC version : DFL61_HARMATTAN_30.2012.07-1.EURASIA
==========
Check : File Is Ok !

Core : v1.48 , FlashEngine : v2.00

Insert cable in to powered OFF phone! (Ignore if phone Connected)
Waiting for NOLO...
Connect in NOLO mode Ok!

Phone Info :
Type : RM-696 , HWRev : 1603
NOLO : 01/06/23
SWVer: DFL61_HARMATTAN_40.2012.21-3.339.2_PR_339
Device mode : Production mode

Read info Ok

Processing APE Boot...
File : DFL61_HARMATTAN_30.2012.07-1_PR_LEGACY_001-OEM1-958_ARM.bin
Processing : ape-algo
APE Algorithm boot Ok

Reopening the connection...

RFS mode init Ok
Device : RM-696
HW build : 1603
Bat.level : 24
SW release : (empty)
Protocol : 108
UPDAPP ver : 1.7.2
Upd/Dev PT : 3 , 3
FL_images : cert-sw,xloader,secondary,rootfs,kernel,moslo,config,mmc,tar,cmt-2nd,cmt-algo,cmt-mcusw
Last errors : bb5_rdc_cert_read failed

Code Match Ok
HW match Ok

RFS : Performing SWAP WIPE...
Starting Wipe...
Bat.level : 24
Battery voltage is enough, starting wipe...
Formatting... Can take up to 15-50 minutes, wait until process complete
Do not disconnect phone, until done!
RFS : Swap format Ok
RFS : No any errors

RFS Set : Host Protocol set to 108
RFS Set : CMT Verify On
RFS Set : Perform RFS On
RFS Set : eMMC preserve On

---Processing MCU image---
Processing File : DFL61_HARMATTAN_30.2012.07-1_PR_LEGACY_001-OEM1-958_ARM.bin
RFS : Sending config for [cert-sw]
-> Ver T : RM-696
-> Ver H : 1507 , 1508 , 1509 , 1510 , 1601 , 1602 , 1603 , 1604 , 1605 , 1701 , 1702 , 1703 , 1704 , 1705 , 1801 , 1802 , 1803 , 1804 , 1805
RFS : Init pipe 00
RFS : Flashing...
RFS : Finalizing...
cert-sw Flash done

RFS : ERROR_SECURITY! Seems as DOWNGRADE TRY!

Receiving error list...
Last Errors : bb5_rdc_cert_read failed
Progress bar initialization failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
Downgrade disallowed (1341314349)
[Pipe 0] Finishing in error state with status 10

Flashing failed
More info in Last Error Log

Elapsed: 00:15:54

И еще лог BEST SW_40.2012.21-3.339.2

Скрытый текст

Connect phone on selected interface...

Check : Processing DFL61_HARMATTAN_40.2012.21-3.339.2_PR_LEGACY_339_ARM_RM-696_PRD_signed.bin
==========
FW APE version : 40.2012.21-3.339.2
FW CMT version : 9.2.2011.51
FW PRx release : PR_1.3
FW Region info : BRANDED TO CARRIER
FW Region ver : 339
KERNEL version : 2.6.32-20121301+0m8
==========
Check : File Is Ok !

Core : v1.48 , FlashEngine : v2.00

Insert cable in to powered OFF phone! (Ignore if phone Connected)
Waiting for NOLO...
Connect in NOLO mode Ok!

Phone Info :
Type : RM-696 , HWRev : 1603
NOLO : 01/06/23
SWVer: DFL61_HARMATTAN_40.2012.21-3.339.2_PR_339
Device mode : Production mode

Read info Ok

Processing APE Boot...
File : DFL61_HARMATTAN_40.2012.21-3.339.2_PR_LEGACY_339_ARM_RM-696_PRD_signed.bin
Processing : ape-algo
APE Algorithm boot Ok

Reopening the connection...

RFS mode init Ok
Device : RM-696
HW build : 1603
Bat.level : 5
SW release : (empty)
Protocol : 108
UPDAPP ver : 1.7.2
Upd/Dev PT : 3 , 3
FL_images : cert-sw,xloader,secondary,rootfs,kernel,moslo,config,mmc,tar,cmt-2nd,cmt-algo,cmt-mcusw
Last errors : bb5_rdc_cert_read failed

Code Match Ok
HW match Ok

Init : 0009
RFS Set : Host Protocol set to 108
RFS Set : CMT Verify On
RFS Set : Perform RFS On
RFS Set : eMMC preserve On

---Processing MCU image---
Processing File : DFL61_HARMATTAN_40.2012.21-3.339.2_PR_LEGACY_339_ARM_RM-696_PRD_signed.bin
RFS : Sending config for [cert-sw]
-> Ver T : RM-696
-> Ver H : 1507 , 1508 , 1509 , 1510 , 1601 , 1602 , 1603 , 1604 , 1605 , 1701 , 1702 , 1703 , 1704 , 1705 , 1801 , 1802 , 1803 , 1804 , 1805
RFS : Init pipe 00
RFS : Flashing...

RFS : ERROR_PIPE_00_LEN_SET FAILED , 0x07 , 0
Receiving error list...
Last errors : Battery level below 10% (current: 5%)
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
No pipe 0 found for PREPARE_DATA_BLOCK_REQ

Лог FLASHER'а

Скрытый текст

C:\meego\Flasher>flasher -F DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_001-OEM1-958_
ARM.bin -f
flasher 3.12.1 (Oct 6 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.

Suitable USB interface (bootloader/phonet) not found, waiting...
Found device RM-696, hardware revision 1603
NOLO version 2.3.6
Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3.339.2_PR_339
Sending ape-algo image (7096 kB)...
100% (7096 of 7096 kB, avg. 20689 kB/s)
Suitable USB interface (phonet) not found, waiting...
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1603
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image moslo not present
Image mmc not present
Image tar skipped
Image config skipped

Battery level 19 %, continuing.

image [state progress transfer flash speed]
---------------------------------------------------------------------
[_] cert-sw [init 0 % 0 / 0 kB NA ]
[ ] cmt-2nd [pending 0 % 0 / 0 kB NA ]
[ ] cmt-algo [pending 0 % 0 / 0 kB NA ]
[ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[ ] xloader [pending 0 % 0 / 0 kB NA ]
[ ] secondary [pending 0 % 0 / 0 kB NA ]
[ ] kernel [pending 0 % 0 / 0 kB NA ]
[ ] rootfs [pending 0 % 0 / 0 kB NA ]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 10: Security failure

image [state progress transfer flash speed]
---------------------------------------------------------------------
[f] cert-sw [init 0 % 1 / 1 kB NA ]
[ ] cmt-2nd [pending 0 % 0 / 0 kB NA ]
[ ] cmt-algo [pending 0 % 0 / 0 kB NA ]
[ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[ ] xloader [pending 0 % 0 / 0 kB NA ]
[ ] secondary [pending 0 % 0 / 0 kB NA ]
[ ] kernel [pending 0 % 0 / 0 kB NA ]
[ ] rootfs [pending 0 % 0 / 0 kB NA ]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
Downgrade disallowed (1341314349)
[Pipe 0] Finishing in error state with status 10
========================================

ERROR: Failed to flash images

C:\meego\Flasher>

16.08.2012, 21:39	#1
ruis Member Регистрация: 23.03.2012 Адрес: Дагестан, Махачкала Сообщений: 42 Вес репутации: 26	Nokia N9 RM-696 не прошивается Телефон принесли на ремонт по причине того что он сильно зависал. Перед прошивкой проверил на наличие вирусов, нашел 2 трояна. Сделал Wipe не помогло. Начал прошивать туже версию Что была в теле, не удалось, потом попробовал 40-ю, тоже не прошился. Пробовал разные версии скачивал с помощью NaviFirm. Прошивка производилась программаторами BEST, Phoenix, Flasher, при прошивке все они кричат что понижение недопустимо. Считывал инфо с помощью беста, там 40-я версия прошивки (изначально была 30-я), делал попытки 30-x, 40-x версий, в т.ч. со своим продукт кодом. Без изменений.. Вот лог BEST SW_30.2012.07-1: Скрытый текст card found: S/N 44XX:XXXX registered to: ruis Connect phone on selected interface... Check : Processing DFL61_HARMATTAN_30.2012.07-1_PR_LEGACY_001-OEM1-958_ARM.bin ========== FW APE version : 30.2012.07-1 FW CMT version : 9.2.2011.50 FW PRx release : PR_1.2 FW Region info : EUROPE [1] , America (Latin , South), South Africa FW Region ver : 001 KERNEL version : 2.6.32-20115101+0m7 ========== Check : File Is Ok ! Check : Processing DFL61_HARMATTAN_30.2012.07-1.EURASIA_EMMC_EURASIA.bin ========== eMMC version : DFL61_HARMATTAN_30.2012.07-1.EURASIA ========== Check : File Is Ok ! Core : v1.48 , FlashEngine : v2.00 Insert cable in to powered OFF phone! (Ignore if phone Connected) Waiting for NOLO... Connect in NOLO mode Ok! Phone Info : Type : RM-696 , HWRev : 1603 NOLO : 01/06/23 SWVer: DFL61_HARMATTAN_40.2012.21-3.339.2_PR_339 Device mode : Production mode Read info Ok Processing APE Boot... File : DFL61_HARMATTAN_30.2012.07-1_PR_LEGACY_001-OEM1-958_ARM.bin Processing : ape-algo APE Algorithm boot Ok Reopening the connection... RFS mode init Ok Device : RM-696 HW build : 1603 Bat.level : 24 SW release : (empty) Protocol : 108 UPDAPP ver : 1.7.2 Upd/Dev PT : 3 , 3 FL_images : cert-sw,xloader,secondary,rootfs,kernel,moslo,config,mmc,tar,cmt-2nd,cmt-algo,cmt-mcusw Last errors : bb5_rdc_cert_read failed Code Match Ok HW match Ok RFS : Performing SWAP WIPE... Starting Wipe... Bat.level : 24 Battery voltage is enough, starting wipe... Formatting... Can take up to 15-50 minutes, wait until process complete Do not disconnect phone, until done! RFS : Swap format Ok RFS : No any errors RFS Set : Host Protocol set to 108 RFS Set : CMT Verify On RFS Set : Perform RFS On RFS Set : eMMC preserve On ---Processing MCU image--- Processing File : DFL61_HARMATTAN_30.2012.07-1_PR_LEGACY_001-OEM1-958_ARM.bin RFS : Sending config for [cert-sw] -> Ver T : RM-696 -> Ver H : 1507 , 1508 , 1509 , 1510 , 1601 , 1602 , 1603 , 1604 , 1605 , 1701 , 1702 , 1703 , 1704 , 1705 , 1801 , 1802 , 1803 , 1804 , 1805 RFS : Init pipe 00 RFS : Flashing... RFS : Finalizing... cert-sw Flash done RFS : ERROR_SECURITY! Seems as DOWNGRADE TRY! Receiving error list... Last Errors : bb5_rdc_cert_read failed Progress bar initialization failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed Downgrade disallowed (1341314349) [Pipe 0] Finishing in error state with status 10 Flashing failed More info in Last Error Log Elapsed: 00:15:54 И еще лог BEST SW_40.2012.21-3.339.2 Скрытый текст Connect phone on selected interface... Check : Processing DFL61_HARMATTAN_40.2012.21-3.339.2_PR_LEGACY_339_ARM_RM-696_PRD_signed.bin ========== FW APE version : 40.2012.21-3.339.2 FW CMT version : 9.2.2011.51 FW PRx release : PR_1.3 FW Region info : BRANDED TO CARRIER FW Region ver : 339 KERNEL version : 2.6.32-20121301+0m8 ========== Check : File Is Ok ! Core : v1.48 , FlashEngine : v2.00 Insert cable in to powered OFF phone! (Ignore if phone Connected) Waiting for NOLO... Connect in NOLO mode Ok! Phone Info : Type : RM-696 , HWRev : 1603 NOLO : 01/06/23 SWVer: DFL61_HARMATTAN_40.2012.21-3.339.2_PR_339 Device mode : Production mode Read info Ok Processing APE Boot... File : DFL61_HARMATTAN_40.2012.21-3.339.2_PR_LEGACY_339_ARM_RM-696_PRD_signed.bin Processing : ape-algo APE Algorithm boot Ok Reopening the connection... RFS mode init Ok Device : RM-696 HW build : 1603 Bat.level : 5 SW release : (empty) Protocol : 108 UPDAPP ver : 1.7.2 Upd/Dev PT : 3 , 3 FL_images : cert-sw,xloader,secondary,rootfs,kernel,moslo,config,mmc,tar,cmt-2nd,cmt-algo,cmt-mcusw Last errors : bb5_rdc_cert_read failed Code Match Ok HW match Ok Init : 0009 RFS Set : Host Protocol set to 108 RFS Set : CMT Verify On RFS Set : Perform RFS On RFS Set : eMMC preserve On ---Processing MCU image--- Processing File : DFL61_HARMATTAN_40.2012.21-3.339.2_PR_LEGACY_339_ARM_RM-696_PRD_signed.bin RFS : Sending config for [cert-sw] -> Ver T : RM-696 -> Ver H : 1507 , 1508 , 1509 , 1510 , 1601 , 1602 , 1603 , 1604 , 1605 , 1701 , 1702 , 1703 , 1704 , 1705 , 1801 , 1802 , 1803 , 1804 , 1805 RFS : Init pipe 00 RFS : Flashing... RFS : ERROR_PIPE_00_LEN_SET FAILED , 0x07 , 0 Receiving error list... Last errors : Battery level below 10% (current: 5%) bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed No pipe 0 found for PREPARE_DATA_BLOCK_REQ Лог FLASHER'а Скрытый текст C:\meego\Flasher>flasher -F DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_001-OEM1-958_ ARM.bin -f flasher 3.12.1 (Oct 6 2011) Harmattan WARNING: This tool is intended for professional use only. Using it may result in permanently damaging your device or losing the warranty. Suitable USB interface (bootloader/phonet) not found, waiting... Found device RM-696, hardware revision 1603 NOLO version 2.3.6 Version of 'sw-release': DFL61_HARMATTAN_40.2012.21-3.339.2_PR_339 Sending ape-algo image (7096 kB)... 100% (7096 of 7096 kB, avg. 20689 kB/s) Suitable USB interface (phonet) not found, waiting... Ping attempt 1 (250 ms) Server application: 1.7.2 Found product RM-696 rev. 1603 Server implements softupd protocol version 1.8 Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001 Image moslo not present Image mmc not present Image tar skipped Image config skipped Battery level 19 %, continuing. image [state progress transfer flash speed] --------------------------------------------------------------------- [_] cert-sw [init 0 % 0 / 0 kB NA ] [ ] cmt-2nd [pending 0 % 0 / 0 kB NA ] [ ] cmt-algo [pending 0 % 0 / 0 kB NA ] [ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ] [ ] xloader [pending 0 % 0 / 0 kB NA ] [ ] secondary [pending 0 % 0 / 0 kB NA ] [ ] kernel [pending 0 % 0 / 0 kB NA ] [ ] rootfs [pending 0 % 0 / 0 kB NA ] ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 10: Security failure image [state progress transfer flash speed] --------------------------------------------------------------------- [f] cert-sw [init 0 % 1 / 1 kB NA ] [ ] cmt-2nd [pending 0 % 0 / 0 kB NA ] [ ] cmt-algo [pending 0 % 0 / 0 kB NA ] [ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ] [ ] xloader [pending 0 % 0 / 0 kB NA ] [ ] secondary [pending 0 % 0 / 0 kB NA ] [ ] kernel [pending 0 % 0 / 0 kB NA ] [ ] rootfs [pending 0 % 0 / 0 kB NA ] Fetching error list: ======================================== bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed bb5_rdc_cert_read failed Downgrade disallowed (1341314349) [Pipe 0] Finishing in error state with status 10 ======================================== ERROR: Failed to flash images C:\meego\Flasher> Последний раз редактировалось ruis; 16.08.2012 в 23:30.