вот лог очень срочно:
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104
CMT_EM_ASIC_ID: 00000C34
CMT_EM_ASIC_ID: 00000C30
CMT_PUBLIC_ID: 15200104675B0344F09A0135D3F0EA8327CBBC87
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC: 3E273BF6
CMT_SECURE_ROM_CRC: 37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.40.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020004000000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020004000000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.40.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: DA2DB2D32C1B2D9886A55B5D8A14F19ADDC53128
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Restarting MCU...
MCU Version V ICPR82_09w39.1
MCU Date 06-10-09
Product RM-547 (Nokia 6730 classic)
Manufacturer (c) Nokia
IMEI 12345610654321?
IMEI Spare 1A32541660452301
IMEI SV 1332541660452321F8000000
PSN CLF541376
Product Code 0583025
Basic Product Code 0574520
PSD 0000000000000000
LPSN 0
APE SW 023.010
APE Variant 023.010023.010.05.01
APE HW 256
APE ADSP 256
APE BT HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.
RETU 34
TAHVO 00
AHNE 11
HW 0500
RFIC |Vapaus_5.1 | Aura_?.?
DSP ICPR82_09w39.1_RIO
Failed to read info -> Failed to read SP info
Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
Writing Product Code...
Writing PSN...
Writing HWID...
Writing Simlock...
Handling as SL3 Simlock Data
Handling as SIMLOCK1 Format
Reading Security Block...
Security block OK and saved to "RM-547_12345610654321_12.01.2012_184046.SecurityBlock.PM"
15 Digits NCK Found
Simlock ACCEPTED OK !
Writing Superdongle key...
Superdongle Key ACCEPTED OK !
Writing CMLA key...
Failed to Write RPL File -> Phone is not responding for Superdongle Request