[chabrus]

Сообщение от UO5OQ

Я не вижу ни малейших признаков неисправности железа.

Я тоже не вижу, но вот некоторые люди не то что утверждают, но даже и настаивают на замене флеш)))

И так, начну

Erase

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C086C769
Using device: HTI, FW ver: 00.50, SN: 00016612
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.19798(05-01-2012), Library ver: 1.0.0.13703(05-01-2012)
CMT Data :
SYSTEM ASIC ID: 000000010000022600010006400C192101021103 [RAPIDO3G ver: 1.11]
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
SecondaryBoot: RAPIDOv11_2nd.fg [BB5] version: 11.34.0 revision: 2.0 size: 0x3B80
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000 - 0000 0000 type: RAM, asic:CMT
Storage1: FFFF 0000 - 0000 0000 type: MMC, asic:CMT
Storage2: 0400 0000 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage3: 0000 0001 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage4: 00EC 0030 - 0000 0121 [Samsung K5W1G13ACM-DJ60,1 Gbits] type: FLASH,MuxOneNAND, asic:CMT
Suggested algorithm: XSR 1.5
Algorithm: RAPIDOv11_XSR15_alg.fg [XSR 1.5] version: 11.34.0 revision: 2.0 size: 0x8FE30
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS HASH: 0FE1BA92D924A658E4800780FA6F4868100AC947
CMT FLASH,MuxOneNAND area [00000000-00FDFFFF]
Erase size: 15.87 MB
Prog.status for Asic CMT ...
NAND: OK

прошивка

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C086C769
Using device: HTI, FW ver: 00.50, SN: 00016612
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.19798(05-01-2012), Library ver: 1.0.0.13703(05-01-2012)
Processing MCU file: rm243_07.10_prd_core.fpsx
[BB5,XSR 1.5] size: 43.63 MB
Supported Ids: 4003192101002003, 400C192101002003, 0003192101002003, 000C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101011105, 400C192101011105, 4003192101021105, 400C192101021105, 400C192101031105, 4003192101031105, 4003192101031103, 400C192101031103, 4003192101051103, 400C192101051103, 4003192101051105, 400C192101051105
CMT Data :
SYSTEM ASIC ID: 000000010000022600010006400C192101021103 [RAPIDO3G ver: 1.11]
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
SecondaryBoot: RAPIDOv11_2nd.fg [BB5] version: 11.34.0 revision: 2.0 size: 0x3B80
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000 - 0000 0000 type: RAM, asic:CMT
Storage1: FFFF 0000 - 0000 0000 type: MMC, asic:CMT
Storage2: FFFF FFFF - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage3: 0000 0001 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage4: 00EC 0030 - 0000 0121 [Samsung K5W1G13ACM-DJ60,1 Gbits] type: FLASH,MuxOneNAND, asic:CMT
Suggested algorithm: XSR 1.5
Algorithm: RAPIDOv11_XSR15_alg.fg [XSR 1.5] version: 11.34.0 revision: 2.0 size: 0x8FE30
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS is blank/erased.
Storing certificate [NPC, CCC, HWC, R&D] ...OK
Partitioning ...OK
Erase size: 74.81 MB
CMT FLASH,MuxOneNAND area [00040000-00082FFF]
CMT FLASH,MuxOneNAND area [00083400-0087FFFF]
CMT FLASH,MuxOneNAND area [00B80000-04DFFFFF]
Formating partition ...
Prog.status for Asic CMT ...
NAND: OK
Flash programming ...
CMT ADA block sent
CMT KEYS block sent
CMT PRIMAPP block sent
CMT RAP3NAND block sent
CMT PASUBTOC block sent
Selecting first CMT PAPUB block with matching RootKey.
CMT PAPUBKEYS: 0FE1BA92 [RAP Certificate 68 v1] sent
CMT SOS*UPDAPP block sent
CMT SOS*DSP0 block sent
CMT SOS*ISASW block sent
CMT SOS*CORE block sent
CMT SOS+ROFS block sent
Prog.status for Asic CMT ...
NAND: OK
Programming completed in 2 min 4.407 s
Processing PPM file: rm243_07.10_prd_vB05_03_russian.fpsx
[BB5,XSR 1.5] size: 23.76 MB
Supported Ids: 4003192101002003, 400C192101002003, 0003192101002003, 000C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101011105, 400C192101011105, 4003192101021105, 400C192101021105, 400C192101031105, 4003192101031105, 4003192101031103, 400C192101031103, 4003192101051103, 400C192101051103, 4003192101051105, 400C192101051105
CMT Data :
SYSTEM ASIC ID: 000000010000022600010006400C192101021103 [RAPIDO3G ver: 1.11]
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
SecondaryBoot: RAPIDOv11_2nd.fg [BB5] version: 11.34.0 revision: 2.0 size: 0x3B80
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000 - 0000 0000 type: RAM, asic:CMT
Storage1: FFFF 0000 - 0000 0000 type: MMC, asic:CMT
Storage2: 0400 0000 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage3: 0000 0001 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage4: 00EC 0030 - 0000 0121 [Samsung K5W1G13ACM-DJ60,1 Gbits] type: FLASH,MuxOneNAND, asic:CMT
Suggested algorithm: XSR 1.5
Algorithm: RAPIDOv11_XSR15_alg.fg [XSR 1.5] version: 11.34.0 revision: 2.0 size: 0x8FE30
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS HASH: 0FE1BA92D924A658E4800780FA6F4868100AC947
Erase size: 27 MB
CMT FLASH,MuxOneNAND area [03300000-04DFFFFF]
Prog.status for Asic CMT ...
NAND: OK
Flash programming ...
CMT SOS+ROFX block sent
Prog.status for Asic CMT ...
NAND: OK
Programming completed in 1 min 15.141 s
Processing CNT file: rm243_07.10_prd_UDA_Pearl_White.fpsx
[BB5,XSR 1.5] size: 111.26 KB
Supported Ids: 4003192101002003, 400C192101002003, 0003192101002003, 000C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101011105, 400C192101011105, 4003192101021105, 400C192101021105
CMT Data :
SYSTEM ASIC ID: 000000010000022600010006400C192101021103 [RAPIDO3G ver: 1.11]
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
SecondaryBoot: RAPIDOv11_2nd.fg [BB5] version: 11.34.0 revision: 2.0 size: 0x3B80
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000 - 0000 0000 type: RAM, asic:CMT
Storage1: FFFF 0000 - 0000 0000 type: MMC, asic:CMT
Storage2: 0400 0000 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage3: 0000 0001 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage4: 00EC 0030 - 0000 0121 [Samsung K5W1G13ACM-DJ60,1 Gbits] type: FLASH,MuxOneNAND, asic:CMT
Suggested algorithm: XSR 1.5
Algorithm: RAPIDOv11_XSR15_alg.fg [XSR 1.5] version: 11.34.0 revision: 2.0 size: 0x8FE30
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS HASH: 0FE1BA92D924A658E4800780FA6F4868100AC947
Erase size: 45.25 MB
CMT FLASH,MuxOneNAND area [04E00000-07B3FFFF]
Prog.status for Asic CMT ...
NAND: OK
Flash programming ...
Prog.status for Asic CMT ...
NAND: OK
Programming completed in 1.421 s
Total time for flashing process(boot+erase+write) was 3 min 47.187 s

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia
Imei plain: 12345610654321-?
Battery voltage: 4575 mV, current: 143 mA
Language Pack:
- not available.

SLPA ver[2]: PA_SL2 (15 digit NCK)

SIMLOCK invalid!
SUPERDONGLE_KEY seems to be valid
SECURITY_TEST failed!


Imei plain is invalid !!!
SIMLOCK_DATA corrupted!
SIMLOCK_DATA corrupted!

Телефон start up filed

Переходим на Best

Erase

User ACCEPTED FULL ERASE
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101021103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.48.0
Processing RAWLOADER...
FLIC : 003000EC
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.48.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done!
TIME : Boot time : 00:00:03
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : 0FE1BA92D924A658E4800780FA6F4868100AC947

CFL: Preparing for erase...

Full Erase started...
Asic : CMT , Sub : NAND
Erase Area 0x00000000-0x07FFFFFF
Erasing Ok , [0F]
Erase done , time : 00:00:01
- > USE "COLD FLASH" option in FlashSetting for revive device by USB!!!

CFL: Erase done

CFL: Close_Session
Content: 000300000000010000000100000000
CFL: Reboot
Phone disconected!

Прошивка

Core version : 1.36 Rev : 1.3

Selected FlashSettings : Cold Flash
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm243_07.10_prd_core.fpsx
PPM : rm243_07.10_prd_vB05_03_russian.fpsx
CNT : rm243_ENO_A_2009wk15v0.100.fpsx
APE : rm243_07.10_prd_UDA_Nokia_Noir.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
- > Force ColdFlash mode
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101021103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.48.0
Processing RAWLOADER...
FLIC : 003000EC
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.48.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done!
TIME : Boot time : 00:00:03
Reopening the connection...
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : Blank (Erased or HW failure)


CFL: phone is in flash mode
===Flashing [MCU]===
Erase : Processing rm243_07.10_prd_core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Data....
Erase area : 0x00040000 - 0x00082FFF , CMT , NAND
Erase area : 0x00083400 - 0x0087FFFF , CMT , NAND
Erase area : 0x00B80000 - 0x04DFFFFF , CMT , NAND
Erase Partition
Partition 0x0A
Erase Ok...
TIME : Erase time : 00:00:01
CFL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

Write : Processing rm243_07.10_prd_core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS*CORE]
CMT: Writing Hash CERT [SOS+ROFS]
Total writen 349 blocks
TIME : Write time : 00:11:55
MCU Write done
CFL: Request programm status
NAND status : 00000001 / 00000001 / 00000000


===Flashing [PPM]===
Erase : Processing rm243_07.10_prd_vB05_03_russian.fpsx
Erasing....
Erasing Data....
Erase area : 0x03300000 - 0x04DFFFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
CFL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

Write : Processing rm243_07.10_prd_vB05_03_russian.fpsx
CMT: Writing Hash CERT [SOS+ROFX]
Total writen 192 blocks
TIME : Write time : 00:06:53
PPM Write done
CFL: Request programm status
NAND status : 00000001 / 00000001 / 00000000


===Flashing [CNT]===
Erase : Processing rm243_ENO_A_2009wk15v0.100.fpsx
Erasing....
Erasing Data....
Erase area : 0x00880000 - 0x00B7FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
CFL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

Write : Processing rm243_ENO_A_2009wk15v0.100.fpsx
CMT: Writing Hash CERT [SOS*ENO]
Total writen 13 blocks
TIME : Write time : 00:00:24
CNT Write done
CFL: Request programm status
NAND status : 00000001 / 00000001 / 00000000


===Flashing [APE]===
Erase : Processing rm243_07.10_prd_UDA_Nokia_Noir.fpsx
Erasing....
Erasing Data....
Erase area : 0x04E00000 - 0x07B3FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
CFL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

Write : Processing rm243_07.10_prd_UDA_Nokia_Noir.fpsx
Total writen 1 blocks
TIME : Write time : 00:00:02
APE Write done
CFL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

CFL: Close_Session
Content: 000300000000010000000100000000
CFL: Reboot

Flashing done!
Total flash time : 00:19:19
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia 6120
Software Info: V 07.10 15-07-09 RM-243 (c) Nokia
IMEI: 12345610654321?
Ape Version: 07.10
Product code:
Checking...
SimLock status : Can't get status
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
ProductTuneSet...OK!
SwUpgradeSet...OK!
AfterFlash operations done ;D
Done!

Elapsed: 00:19:44
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Теперь телефон запустился и работает.
Дальше работаем с МХкеу

Заливка Вашего RPL

Imei: 35864101395133
Updating SIMLOCK ...error 0x1
Updating SUPERDONGLE_KEY ...error 0x3
Updating CMLA_KEY ...OK
MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C086C769
Using device: HTI, FW ver: 00.50, SN: 00016612
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.19798(05-01-2012), Library ver: 1.0.0.13703(05-01-2012)
CMT Data :
SYSTEM ASIC ID: 000000010000022600010006400C192101021103 [RAPIDO3G ver: 1.11]
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
SecondaryBoot: RAPIDOv11_2nd.fg [BB5] version: 11.34.0 revision: 2.0 size: 0x3B80
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
eBB5ProtocolType: NEW
TransmissionMode: DDR&TX2
Storage0: 0000 0000 - 0000 0000 type: RAM, asic:CMT
Storage1: FFFF 0000 - 0000 0000 type: MMC, asic:CMT
Storage2: 0400 0000 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage3: 0000 0001 - 0000 0000 [unused/removed] type: FLASH,NOR, asic:CMT
Storage4: 00EC 0030 - 0000 0121 [Samsung K5W1G13ACM-DJ60,1 Gbits] type: FLASH,MuxOneNAND, asic:CMT
Suggested algorithm: XSR 1.5
Algorithm: RAPIDOv11_XSR15_alg.fg [XSR 1.5] version: 11.34.0 revision: 2.0 size: 0x8FE30
Supported Ids: 0003192101001203, 000C192101001203, 4003192101001203, 400C192101001203, 0003192101002003, 000C192101002003, 4003192101002003, 400C192101002003, 4003192101011103, 400C192101011103, 4003192101021103, 400C192101021103, 4003192101031103, 400C192101031103, 4003192101011105, 400C192101011105, 400C192101021105, 400C192101031105, 4003192101051103, 400C192101051103, 400C192101051105, 4003192101051105
TransmissionMode: DDR&TX2
FUR: Adding Asic CMT as client OK
CMT PAPUBKEYS HASH: 0FE1BA92D924A658E4800780FA6F4868100AC947
Updating CMT NPC ...OK
Updating CMT CCC ...OK
Updating CMT HWC ...OK
Prog.status for Asic CMT ...
NAND: OK

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia
Imei plain: 35864101395133-9
Battery voltage: 4668 mV, current: 116 mA
ApeCoreSw: 07.10
Language Pack:
- not available.

SLPA ver[1]: PA_SL (15 digit NCK)

SIMLOCK invalid!
SUPERDONGLE_KEY invalid!
- WD timer enabled, phone will reboot itself after 3 min.
SECURITY_TEST passed


SIMLOCK_DATA corrupted!
SIMLOCK_DATA corrupted!

Scan

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia
Imei plain: 35864101395133-9
Battery voltage: 4507 mV, current: 147 mA
ApeCoreSw: 07.10
Language Pack:
- not available.

SLPA ver[1]: PA_SL (15 digit NCK)

SIMLOCK invalid!
SUPERDONGLE_KEY invalid!
- WD timer enabled, phone will reboot itself after 3 min.
SECURITY_TEST passed


SIMLOCK_DATA corrupted!
SIMLOCK_DATA corrupted!

Update SP Lock

SIMLOCK_DATA corrupted!
SIMLOCK_DATA corrupted!
MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C086C769
Using device: HTI, FW ver: 00.50, SN: 00016612
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.19798(05-01-2012), Library ver: 1.0.0.13703(05-01-2012)

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia
ApeCoreSw: 07.10

Using cached productData.
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
PRIVATE ID: 810230AA7EE2C1E7B8893C5E60E2BDD0AB48D616
Updating SIMLOCK ...OK

Reading Simlock info ...
Imei net: 358641013951339
Version: SIMLOCK SERVER
Counter: 0/3, 0/10

CONFIG_DATA: 2440700000000000
PROFILE_BITS: 0000000000000000

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN

Scan

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia
Imei plain: 35864101395133-9
Battery voltage: 4688 mV, current: 154 mA
ApeCoreSw: 07.10
Language Pack:
- not available.

SLPA ver[2]: PA_SL2 (15 digit NCK)

SIMLOCK seems to be valid
SUPERDONGLE_KEY invalid!
- WD timer enabled, phone will reboot itself after 3 min.
SECURITY_TEST passed


Imei net: 358641013951339
Version: SIMLOCK SERVER
Counter: 0/3, 0/10

CONFIG_DATA: 2440700000000000
PROFILE_BITS: 0000000000000000

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN

Repair SD

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C086C769
Using device: HTI, FW ver: 00.50, SN: 00016612
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.19798(05-01-2012), Library ver: 1.0.0.13703(05-01-2012)

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia
ApeCoreSw: 07.10

Using cached productData.
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
PRIVATE ID: 810230AA7EE2C1E7B8893C5E60E2BDD0AB48D616
Updating SUPERDONGLE_KEY ...OK
Authenticating to SUPERDONGLE ...
SUPERDONGLE authorized !
Now you can write RFBB/PM data to the phone.
Done.

Scan

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia
Imei plain: 35864101395133-9
Battery voltage: 4583 mV, current: 121 mA
ApeCoreSw: 07.10
Language Pack:
- not available.

SLPA ver[2]: PA_SL2 (15 digit NCK)

SIMLOCK seems to be valid
SUPERDONGLE_KEY seems to be valid
SECURITY_TEST failed!


Imei net: 358641013951339
Version: SIMLOCK SERVER
Counter: 0/3, 0/10

CONFIG_DATA: 2440700000000000
PROFILE_BITS: 0000000000000000

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN

Запись РМ

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C086C769
Using device: HTI, FW ver: 00.50, SN: 00016612
Connection status: UHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0
Module ver: 1.0.0.19798(05-01-2012), Library ver: 1.0.0.13703(05-01-2012)

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia
ApeCoreSw: 07.10

Using cached productData.
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
PRIVATE ID: 810230AA7EE2C1E7B8893C5E60E2BDD0AB48D616
SUPERDONGLE authorized !
SERVER->MXKEY - BLADE X at host1, agent version 1.2 revision 0.2

Updating RFBB data ...
Writing section 1...
Writing section 309...
Done.

Scan

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia
Imei plain: 35864101395133-9
Battery voltage: 4688 mV, current: 140 mA
ApeCoreSw: 07.10
Language Pack:
- not available.

SLPA ver[2]: PA_SL2 (15 digit NCK)

SIMLOCK seems to be valid
SUPERDONGLE_KEY seems to be valid
SECURITY_TEST failed!


Imei net: 358641013951339
Version: SIMLOCK SERVER
Counter: 0/3, 0/10

CONFIG_DATA: 2440700000000000
PROFILE_BITS: 0000000000000000

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN

Не включается. Start Up Filed.

Позже попробую другими продуктами.
Отпишусь.

Вчера был аналогичный случай с 3110с.
Та же беда. Обратил внимание на то, что телефон стирается через раз, и не всегда корректно. Заменил на нем флешку, и после стирания, прошивки и прочих танцев тело завелось.

После того решил последовать этому примеру.
Перекатал проц, заменил флеш на заведомо исправную.
И вот:

Стирание

User ACCEPTED FULL ERASE
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101021103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 003000EC
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done!
TIME : Boot time : 00:00:03
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : Blank (Erased or HW failure)

CFL: Preparing for erase...

Full Erase started...
Asic : CMT , Sub : NAND
Erase Area 0x00000000-0x07FFFFFF
Erasing Ok , [0F]
Erase done , time : 00:00:01
- > USE "COLD FLASH" option in FlashSetting for revive device by USB!!!

CFL: Erase done

CFL: Close_Session
Content: 000300000000000000000000000000
CFL: Reboot
Phone disconected!

Прошивка

Files Set for Flashing :
MCU : rm243_07.10_prd_core.fpsx
PPM : rm243_07.10_prd_vB01_03_euro1.fpsx
CNT : rm243_ENO_A_2009wk15v0.100.fpsx
APE : rm243_07.10_prd_UDA_Nokia_Noir.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
- > Force ColdFlash mode
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101021103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 003000EC
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done!
TIME : Boot time : 00:00:03
Reopening the connection...
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : Blank (Erased or HW failure)


CFL: phone is in flash mode
===Flashing [MCU]===
Erase : Processing rm243_07.10_prd_core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Data....
Erase area : 0x00040000 - 0x00082FFF , CMT , NAND
Erase area : 0x00083400 - 0x0087FFFF , CMT , NAND
Erase area : 0x00B80000 - 0x04DFFFFF , CMT , NAND
Erase Partition
Partition 0x0A
Erase Ok...
TIME : Erase time : 00:00:01
CFL: Request programm status
NAND status : 00000000 / 00000000 / 00000000

Write : Processing rm243_07.10_prd_core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS*CORE]
CMT: Writing Hash CERT [SOS+ROFS]
Total writen 349 blocks
TIME : Write time : 00:12:01
MCU Write done
CFL: Request programm status
NAND status : 00000000 / 00000000 / 00000000


===Flashing [PPM]===
Erase : Processing rm243_07.10_prd_vB01_03_euro1.fpsx
Erasing....
Erasing Data....
Erase area : 0x03300000 - 0x04DFFFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
CFL: Request programm status
NAND status : 00000000 / 00000000 / 00000000

Write : Processing rm243_07.10_prd_vB01_03_euro1.fpsx
CMT: Writing Hash CERT [SOS+ROFX]
Total writen 179 blocks
TIME : Write time : 00:06:26
PPM Write done
CFL: Request programm status
NAND status : 00000000 / 00000000 / 00000000


===Flashing [CNT]===
Erase : Processing rm243_ENO_A_2009wk15v0.100.fpsx
Erasing....
Erasing Data....
Erase area : 0x00880000 - 0x00B7FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
CFL: Request programm status
NAND status : 00000000 / 00000000 / 00000000

Write : Processing rm243_ENO_A_2009wk15v0.100.fpsx
CMT: Writing Hash CERT [SOS*ENO]
Total writen 13 blocks
TIME : Write time : 00:00:24
CNT Write done
CFL: Request programm status
NAND status : 00000000 / 00000000 / 00000000


===Flashing [APE]===
Erase : Processing rm243_07.10_prd_UDA_Nokia_Noir.fpsx
Erasing....
Erasing Data....
Erase area : 0x04E00000 - 0x07B3FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
CFL: Request programm status
NAND status : 00000000 / 00000000 / 00000000

Write : Processing rm243_07.10_prd_UDA_Nokia_Noir.fpsx
Total writen 1 blocks
TIME : Write time : 00:00:02
APE Write done
CFL: Request programm status
NAND status : 00000000 / 00000000 / 00000000

CFL: Close_Session
Content: 000300000000000000000000000000
CFL: Reboot

Flashing done!
Total flash time : 00:18:58
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia 6120
Software Info: V 07.10 15-07-09 RM-243 (c) Nokia
IMEI: 12345610654321?
Ape Version: 07.10
Product code:
Checking...
SimLock status : Can't get status
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
ProductTuneSet...OK!
SwUpgradeSet...OK!
AfterFlash operations done ;D
Done!

Elapsed: 00:19:21
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Заливка только NPC

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101021103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 003000EC
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done!
TIME : Boot time : 00:00:03
Reopening the connection...
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : 0FE1BA92D924A658E4800780FA6F4868100AC947

ADL: Preparing for write certificates...

Erase NPC... Ok
Writing NPC... Ok

ADL: Writing Flash certs done!

CFL: Close_Session
Content: 000300000000000000000000000000
CFL: Reboot

-> No any Flex keys selected, skip flex part

Done!

Phone disconected!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Write CCC/HWC

Will Write CCC/HWC keys now...

Using : RM-243.rpl
CCC Data found!
HWC Data found!

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101021103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15000101E47D0058F37E90230F88DCC677278E32
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: A8C1D6713E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 003000EC
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done!
TIME : Boot time : 00:00:03
Reopening the connection...
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : 0FE1BA92D924A658E4800780FA6F4868100AC947

CFL: Preparing for write certificates...

Erase CCC... Ok
Writing CCC... Ok
Erase HWC... Ok
Writing HWC... Ok

CFL: Writing Flash certs done!

CFL: Close_Session
Content: 000300000000000000000000000000
CFL: Reboot
All done, disconneting...

Done!

Elapsed: 00:00:14

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Восстановление SL

Repair SL procedure started...

Phone Imei: 358641013951339
Key file exists, no need to read...
Operating mode is OK, no need change...
Writing SimLock Data...   Ok!
Writing SimLock Key...   Ok!
Done!

Восстановление SD

Repair SD procedure started...

Phone Imei: 358641013951339
Key file exists, no need to read...
Operating mode is OK, no need change...
Writing Super Dongle Key...   Error
Repair fail...!

Значит все таки не железо.
Что посоветуете теперь?

Checking StartUp data ...
-----------------------

SDD Key status : SDData Damaged!!!!! :(
 - > Do REPAIR SDD , Local SX4 if needed 

SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version : 
PA_SL phone detected

Done!

Дальше, решил для интереса поработать с MXkey

[HIDE="30"]
При первом же скане, программа показала что в теле все таки битый sim lock
Вобщем повторил все стандартные процедуры, которые описывал в предыдущих постах. К сожалению не сохранил логи, счев это не нужным и не надеясь на результат.
Картина точь в точь повторилась, удается восстановить SL и SD через сервер. Пролился 1-309 поля РМ. Но при скане было все то же security tast filed.
Решил пролить полный РМ. При его заливке программа ругнулась на 120 блок и спросила разрешения переписать параметры sim lock.

После этого я увидел вот такой вот лог:

Phone type: RM-243 (Nokia 6120)
SW version: V 07.10 15-07-09 RM-243 (c) Nokia 
Imei plain: 35864101395133-9
Product code: 0546333
Battery voltage: 4575 mV, current: 132 mA
ApeCoreSw: 07.10
Language Pack:
- not available.

SLPA ver[2]: PA_SL2 (15 digit NCK)
 
SIMLOCK seems to be valid
SUPERDONGLE_KEY seems to be valid
SECURITY_TEST passed
 
 
Imei net: 358641013951339
Version: SIMLOCK SERVER
Counter: 0/3, 0/10
 
CONFIG_DATA: 2440700000000000
PROFILE_BITS: 0000000000000000
 
BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN

Проверю тело, по результату отпишусь.
Если есть соображения по поводу, прошу отписывать. Если есть интерес разработчиков, могу повторить все с нуля bestom чтобы узнать в чем именно ошибка.
По моему варианта 2:
1- best не смог поправить securiti в связи с особенностями данной модели, и сначала нужно было влить РМ, перед тем как восстанавливать SD.
2- файлы SL и SD от данной модели, которые заливает программа, повреждены или не правильные.

Вот check с Bestом

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version : 
PA_SL2 phone detected

Done!

[/HIDE]

За сим, тему думаю можно закрыть.