Лог MX-KEY по кнопке SCAN:

Shuhauz · 13.11.2011, 22:07

Принесли телефон на прошивку во включенном виде, прошил и после того тело уснуло в локал перестало входить.
Сзади было написанно что RM-718, а я подумал что внутри RM-601 и прошил как RM-601, ноль эмоций. Пришлось его стереть. Стер и тело включилось но c битым RPL заказал RPL. Хочу залить RPL не получается BEST не хочет заливать Sim lock а Cyclone тоже не залил но вот MX key залил SIM Lock но security никак не хочет залить. Прошу помочь в этом геморе. Best заливает с авторизацией и пишет ОК также и Cyclone пишет ОК, но MX-Key показывает что не залил. ((((

**UO5OQ** · 13.11.2011, 22:14

Давайте посмотрим логи.
1.) Лог от MX-BOX по кнопке "SCAN"
2.) Лог SX4 авторизации и записи PM от BEST.

Shuhauz · 13.11.2011, 22:22

вот логи Best и MX KEY.

Лог MX-KEY по кнопке SCAN:

Phone Type: RM-718 (Nokia C6-01)
SW Version: V 92_11w25.1 01-07-11 RM-718 (c) Nokia
Imei plain: 358xxxxxxx
Battery voltage: 4284 mV, current: 77 mA
ApeCoreSw: 022.014
Language Pack:
- not available.

Detected as PA_SL3 phone.
- Avoid SW Downgrade & manual erase to this phone !

SIMLOCK invalid!
SUPERDONGLE_KEY seems to be valid
CMLA_KEY seems to be valid
WMDRM_PD seems to be valid
SIMLOCK_TEST passed
SECURITY_TEST failed!

Imei net: 358xxxxxxx
Version: SIMLOCK SERVER
Counter: 0/3, 0/10

CONFIG_DATA: 2440700000000000
PROFILE_BITS: 0000000000000000

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN

Лог BEST Repair SD, локальной SX4 и записи PM:

Repair SD procedure started...

Phone Imei: 358xxxxxxxxxxx
Key file exists, no need to read...
Accepted SdRepReq (on alive SD) by user
Check phone mode...
Phone in SelftestFail mode
Seting Test mode... wait...
Test mode set
Writing Super Dongle Key... Ok
Done!

Local SX4 procedure started...

Phone Imei: 358xxxxxxxx
Use custom key...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Upload PM checked
Uploading RF/Battery tune to phone...
Using : RM-718.pm
Check phone mode...
Phone in SelftestFail mode
Seting Local mode... wait...
Local mode set

Field 1
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 6 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 15 write - Ok
Record 16 write - Ok
Record 17 write - Ok
Record 18 write - Ok
Record 19 write - Ok
Record 22 write - Ok
Record 26 write - Ok
Record 27 write - Ok
Record 28 write - Ok
Record 29 write - Ok
Record 30 write - Ok
Record 31 write - Ok
Record 32 write - Ok
Record 33 write - Ok
Record 35 write - Ok
Record 36 write - Ok
Record 38 write - Ok
Record 39 write - Ok
Record 40 write - Ok
Record 41 write - Ok
Record 43 write - Ok
Record 44 write - Ok
Record 45 write - Ok
Field 2
Record 0 write - Ok
Field 309
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 7 write - Ok
Record 17 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => DAMAGED

- > Try different PM files or "Restore CCC/HWC" option

Done!

Elapsed: 00:00:16

Upload done

**UO5OQ** · 13.11.2011, 22:38

По логу SCAN видно, что RPL сделал своё дело на 100%
Все CRT DATA восстановлены.
SECURITY_TEST failed! - исправляется SX4 авторизацией телефона и записью PM 1 и 309 полей непосредственно сразу после успешного прохождения SX4 авторизации.

После записи заводского RPL всегда очень желательно делать настоящую серверную SX4 авторизацию, особенно на новых моделях телефонов. Не надо делать SDD Repair.

- Запишите RPL ещё раз чем записывали.
- Потом в Cyclone Box поставьте галочку на "Force Using SX4 Server" затем кликните на "Authorize / Repair SD Keys" и если SX4 пройдёт то записывайте C6-01_RM-718_www.UO5OQ.com_PM по кнопке "Write PM"

Примечание: Настоящая, серверная SX4 авторизация у всех Боксов часто проходит с 2-3-4...-35... раза, в зависимости от нагрузки на их SX4 сервер и вашего И-нет соединения.

Shuhauz · 13.11.2011, 23:17

Вот лог SX4 авторизации и записи Virgin PM из Database сервера Cyclone Box:

SX4 Status: Not authorized (74)
Started mutual authenthication with card...
Cyclone Server (1.0.0.677), Cyclone Box Team 2008-2011 - Ready.
Receiving Phone Seed 1...
Phone Seed 1 Received
Sending calculated Data 1, and expecting Seed 2...
Calculated Data 1 accepted, Phone Seed 2 Received
Sending calculated Data 2
Calculated Data 2 sent, Checking Authorization Status again
Authorization successfully finished!
Looking for Virgin PM In Database...
Found, writing...
[1,0] Written, Length: 10 bytes, Status: OK
[1,1] Written, Length: 94 bytes, Status: OK
[1,2] Written, Length: 110 bytes, Status: OK
[1,4] Written, Length: 10 bytes, Status: OK
[1,6] Written, Length: 110 bytes, Status: OK
[1,7] Written, Length: 450 bytes, Status: OK
[1,8] Written, Length: 10 bytes, Status: OK
[1,13] Written, Length: 110 bytes, Status: OK
[1,15] Written, Length: 30 bytes, Status: OK
[1,16] Written, Length: 30 bytes, Status: OK
[1,17] Written, Length: 30 bytes, Status: OK
[1,18] Written, Length: 30 bytes, Status: OK
[1,19] Written, Length: 30 bytes, Status: OK
[1,22] Written, Length: 24 bytes, Status: OK
[1,26] Written, Length: 10 bytes, Status: OK
[1,27] Written, Length: 36 bytes, Status: OK
[1,28] Written, Length: 110 bytes, Status: OK
[1,29] Written, Length: 10 bytes, Status: OK
[1,30] Written, Length: 36 bytes, Status: OK
[1,31] Written, Length: 24 bytes, Status: OK
[1,32] Written, Length: 216 bytes, Status: OK
[1,33] Written, Length: 36 bytes, Status: OK
[1,35] Written, Length: 24 bytes, Status: OK
[1,36] Written, Length: 24 bytes, Status: OK
[1,38] Written, Length: 216 bytes, Status: OK
[1,39] Written, Length: 36 bytes, Status: OK
[1,40] Written, Length: 24 bytes, Status: OK
[1,41] Written, Length: 216 bytes, Status: OK
[1,43] Written, Length: 36 bytes, Status: OK
[1,44] Written, Length: 216 bytes, Status: OK
[1,45] Written, Length: 216 bytes, Status: OK
[2,0] Written, Length: 2240 bytes, Status: OK
[309,0] Written, Length: 4 bytes, Status: OK
[309,1] Written, Length: 2 bytes, Status: OK
[309,2] Written, Length: 12 bytes, Status: OK
[309,3] Written, Length: 36 bytes, Status: OK
[309,4] Written, Length: 12 bytes, Status: OK
[309,7] Written, Length: 12 bytes, Status: OK
[309,17] Written, Length: 12 bytes, Status: OK
Write PM Finished, Record written OK: 39, Record written NOT OK: 0
Disconnected from Cyclone Server
[1,0] Written, Length: 10 bytes, Status: OK
[1,1] Written, Length: 94 bytes, Status: OK
[1,2] Written, Length: 110 bytes, Status: OK
[1,4] Written, Length: 10 bytes, Status: OK
[1,6] Written, Length: 110 bytes, Status: OK
[1,7] Written, Length: 450 bytes, Status: OK
[1,8] Written, Length: 10 bytes, Status: OK
[1,13] Written, Length: 110 bytes, Status: OK
[1,15] Written, Length: 30 bytes, Status: OK
[1,16] Written, Length: 30 bytes, Status: OK
[1,17] Written, Length: 30 bytes, Status: OK
[1,18] Written, Length: 30 bytes, Status: OK
[1,19] Written, Length: 30 bytes, Status: OK
[1,22] Written, Length: 24 bytes, Status: OK
[1,26] Written, Length: 10 bytes, Status: OK
[1,27] Written, Length: 36 bytes, Status: OK
[1,28] Written, Length: 110 bytes, Status: OK
[1,29] Written, Length: 10 bytes, Status: OK
[1,30] Written, Length: 36 bytes, Status: OK
[1,31] Written, Length: 24 bytes, Status: OK
[1,32] Written, Length: 216 bytes, Status: OK
[1,33] Written, Length: 36 bytes, Status: OK
[1,35] Written, Length: 24 bytes, Status: OK
[1,36] Written, Length: 24 bytes, Status: OK
[1,38] Written, Length: 216 bytes, Status: OK
[1,39] Written, Length: 36 bytes, Status: OK
[1,40] Written, Length: 24 bytes, Status: OK
[1,41] Written, Length: 216 bytes, Status: OK
[1,43] Written, Length: 36 bytes, Status: OK
[1,44] Written, Length: 216 bytes, Status: OK
[1,45] Written, Length: 216 bytes, Status: OK
[309,0] Written, Length: 4 bytes, Status: OK
[309,1] Written, Length: 2 bytes, Status: OK
[309,2] Written, Length: 12 bytes, Status: OK
[309,3] Written, Length: 36 bytes, Status: OK
[309,4] Written, Length: 12 bytes, Status: OK
[309,7] Written, Length: 12 bytes, Status: OK
[309,17] Written, Length: 12 bytes, Status: OK
Write PM Finished, Record written OK: 38, Record written NOT OK: 0

Лог Cyclone Box, Security Analyse:

Started Phone Security Analysis...
MCU Version V 92_11w25.1
MCU Date 01-07-11
Product RM-718 (Nokia C6-01)
Manufacturer (c) Nokia
IMEI 35xxxxxxxxxxxxxxxxx
Mastercode 145263546
Reading Security Block...
Security block OK and saved to "RM-718_35xxxxxxxxxxx_14.11.2011_22629.SecurityBlock.PM"
Step 1 : Testing SIMLOCK
SIMLOCK SEFLTEST PASSED OK!
Step 2 : Testing SECURITY
-- SECURITY PROBLEM --

Phone have failed SECURITY Test, that means Superdongle Area is DAMAGED!
To repair it, simply slick "SX4 Authorization / SD Repair" button.
After SX4/SD Repair, don't forget to write PM file with fields 1,309 (if SW don't do this automatically)

Additionaly, Checking HWC/CCC Certs...
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00001040
CMT_EM_ASIC_ID: 00001030
CMT_PUBLIC_ID: 0F40020C66AC03225A84B9358468328C9FF6D9A0
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.16.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC006000000032, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0060 (Samsung), Size: 1024MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.16.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: A676DE8B3DEA6D6C6FFE9CBE15A7C501CC822B23
APE Subsystem Not Found
Flashbus Write baud set to 5.0Mbits
HWC Looks OK!
CCC Looks OK!
Restarting MCU...
-- SECURITY PROBLEM --
Step 3 : Analyzing Security Block
"0F40020C66AC03225A84B9358468328C9FF6D9A0.C0004076" Exists, That is good...
Checking SUPERDONGLE...
SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
Checking SIMLOCK...
Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
Checking MCU&DSP TIMESTAMPS...
MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
Checking CMLA KEYS...
CMLA KEYS FOUND AND CHECKSUM OK! PASSED!
Checking ECC KEYS...
ECC KEYS FOUND AND CHECKSUM OK! PASSED!
Checking DIV KEYS...
DIV KEYS FOUND AND CHECKSUM OK! PASSED!
Analyze finished!

**UO5OQ** · 13.11.2011, 23:47

Хм... Интересный случай, видимо особенности модели.
Настоящая серверная SX4 авторизация прошла, PM 1 и 309 поля успешно записались, а SECURITY_TEST failed! остался.

Попробуйте SX4 авторизацию от BEST, но с этим полным PM C6-01_RM-718_www.UO5OQ.com_Full_PM

В общем пробуйте все варианты всеми доступными вам боксами.
1 вариант: настоящая SX4 авторизация, запись разных PM
2 вариант: Repair SD, локальная SX4 авторизация, запись разных PM
3 вариант: Запись парных - считанных из одного телефона HWC+CCC и PM с SX4 конечно
P.S. (не уверен что я тут выложил парные HWC+CCC и PM) желательно найти рабочий C6-01_RM-718 и вычитать из него парные.

Shuhauz · 16.11.2011, 19:33

Сделал я этот тело.Слил с рабочего тела и залил HWC+CCC.Тему мона закрыть!!!!

13.11.2011, 22:07	#1
Shuhauz Senior Member Регистрация: 19.04.2011 Сообщений: 304 Вес репутации: 79	Nokia C6-01 RM-718 после неудачной прошивки Принесли телефон на прошивку во включенном виде, прошил и после того тело уснуло в локал перестало входить. Сзади было написанно что RM-718, а я подумал что внутри RM-601 и прошил как RM-601, ноль эмоций. Пришлось его стереть. Стер и тело включилось но c битым RPL заказал RPL. Хочу залить RPL не получается BEST не хочет заливать Sim lock а Cyclone тоже не залил но вот MX key залил SIM Lock но security никак не хочет залить. Прошу помочь в этом геморе. Best заливает с авторизацией и пишет ОК также и Cyclone пишет ОК, но MX-Key показывает что не залил. ((((

13.11.2011, 22:14	#2
UO5OQ ADMINISTRATOR Регистрация: 01.01.2011 Адрес: www.UO5OQ.com Сообщений: 14,724 Вес репутации: 10	Re: Nokia C6-01 RM-718 после неудачной прошивки Давайте посмотрим логи. 1.) Лог от MX-BOX по кнопке "SCAN" 2.) Лог SX4 авторизации и записи PM от BEST. __________________ Разблокировка iPhone, NCK Коды, Логи и Активации на www.UO5OQ.com

13.11.2011, 22:22	#3
Shuhauz Senior Member Регистрация: 19.04.2011 Сообщений: 304 Вес репутации: 79	Re: Nokia C6-01 RM-718 после неудачной прошивки вот логи Best и MX KEY. Лог MX-KEY по кнопке SCAN: Phone Type: RM-718 (Nokia C6-01) SW Version: V 92_11w25.1 01-07-11 RM-718 (c) Nokia Imei plain: 358xxxxxxx Battery voltage: 4284 mV, current: 77 mA ApeCoreSw: 022.014 Language Pack: - not available. Detected as PA_SL3 phone. - Avoid SW Downgrade & manual erase to this phone ! SIMLOCK invalid! SUPERDONGLE_KEY seems to be valid CMLA_KEY seems to be valid WMDRM_PD seems to be valid SIMLOCK_TEST passed SECURITY_TEST failed! Imei net: 358xxxxxxx Version: SIMLOCK SERVER Counter: 0/3, 0/10 CONFIG_DATA: 2440700000000000 PROFILE_BITS: 0000000000000000 BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN Лог BEST Repair SD, локальной SX4 и записи PM: Repair SD procedure started... Phone Imei: 358xxxxxxxxxxx Key file exists, no need to read... Accepted SdRepReq (on alive SD) by user Check phone mode... Phone in SelftestFail mode Seting Test mode... wait... Test mode set Writing Super Dongle Key... Ok Done! Local SX4 procedure started... Phone Imei: 358xxxxxxxx Use custom key... Step 1... Step 2... Step 3... SX4 Auth - Ok Upload PM checked Uploading RF/Battery tune to phone... Using : RM-718.pm Check phone mode... Phone in SelftestFail mode Seting Local mode... wait... Local mode set Field 1 Record 0 write - Ok Record 1 write - Ok Record 2 write - Ok Record 4 write - Ok Record 6 write - Ok Record 7 write - Ok Record 8 write - Ok Record 13 write - Ok Record 15 write - Ok Record 16 write - Ok Record 17 write - Ok Record 18 write - Ok Record 19 write - Ok Record 22 write - Ok Record 26 write - Ok Record 27 write - Ok Record 28 write - Ok Record 29 write - Ok Record 30 write - Ok Record 31 write - Ok Record 32 write - Ok Record 33 write - Ok Record 35 write - Ok Record 36 write - Ok Record 38 write - Ok Record 39 write - Ok Record 40 write - Ok Record 41 write - Ok Record 43 write - Ok Record 44 write - Ok Record 45 write - Ok Field 2 Record 0 write - Ok Field 309 Record 0 write - Ok Record 1 write - Ok Record 2 write - Ok Record 3 write - Ok Record 4 write - Ok Record 7 write - Ok Record 17 write - Ok Check ST_SECURITY now... Security status : ST_SECURITY => DAMAGED - > Try different PM files or "Restore CCC/HWC" option Done! Elapsed: 00:00:16 Upload done

13.11.2011, 23:17	#5
Shuhauz Senior Member Регистрация: 19.04.2011 Сообщений: 304 Вес репутации: 79	Вот лог SX4 авторизации и записи Virgin PM из Database сервера Cyclone Box: SX4 Status: Not authorized (74) Started mutual authenthication with card... Cyclone Server (1.0.0.677), Cyclone Box Team 2008-2011 - Ready. Receiving Phone Seed 1... Phone Seed 1 Received Sending calculated Data 1, and expecting Seed 2... Calculated Data 1 accepted, Phone Seed 2 Received Sending calculated Data 2 Calculated Data 2 sent, Checking Authorization Status again Authorization successfully finished! Looking for Virgin PM In Database... Found, writing... [1,0] Written, Length: 10 bytes, Status: OK [1,1] Written, Length: 94 bytes, Status: OK [1,2] Written, Length: 110 bytes, Status: OK [1,4] Written, Length: 10 bytes, Status: OK [1,6] Written, Length: 110 bytes, Status: OK [1,7] Written, Length: 450 bytes, Status: OK [1,8] Written, Length: 10 bytes, Status: OK [1,13] Written, Length: 110 bytes, Status: OK [1,15] Written, Length: 30 bytes, Status: OK [1,16] Written, Length: 30 bytes, Status: OK [1,17] Written, Length: 30 bytes, Status: OK [1,18] Written, Length: 30 bytes, Status: OK [1,19] Written, Length: 30 bytes, Status: OK [1,22] Written, Length: 24 bytes, Status: OK [1,26] Written, Length: 10 bytes, Status: OK [1,27] Written, Length: 36 bytes, Status: OK [1,28] Written, Length: 110 bytes, Status: OK [1,29] Written, Length: 10 bytes, Status: OK [1,30] Written, Length: 36 bytes, Status: OK [1,31] Written, Length: 24 bytes, Status: OK [1,32] Written, Length: 216 bytes, Status: OK [1,33] Written, Length: 36 bytes, Status: OK [1,35] Written, Length: 24 bytes, Status: OK [1,36] Written, Length: 24 bytes, Status: OK [1,38] Written, Length: 216 bytes, Status: OK [1,39] Written, Length: 36 bytes, Status: OK [1,40] Written, Length: 24 bytes, Status: OK [1,41] Written, Length: 216 bytes, Status: OK [1,43] Written, Length: 36 bytes, Status: OK [1,44] Written, Length: 216 bytes, Status: OK [1,45] Written, Length: 216 bytes, Status: OK [2,0] Written, Length: 2240 bytes, Status: OK [309,0] Written, Length: 4 bytes, Status: OK [309,1] Written, Length: 2 bytes, Status: OK [309,2] Written, Length: 12 bytes, Status: OK [309,3] Written, Length: 36 bytes, Status: OK [309,4] Written, Length: 12 bytes, Status: OK [309,7] Written, Length: 12 bytes, Status: OK [309,17] Written, Length: 12 bytes, Status: OK Write PM Finished, Record written OK: 39, Record written NOT OK: 0 Disconnected from Cyclone Server [1,0] Written, Length: 10 bytes, Status: OK [1,1] Written, Length: 94 bytes, Status: OK [1,2] Written, Length: 110 bytes, Status: OK [1,4] Written, Length: 10 bytes, Status: OK [1,6] Written, Length: 110 bytes, Status: OK [1,7] Written, Length: 450 bytes, Status: OK [1,8] Written, Length: 10 bytes, Status: OK [1,13] Written, Length: 110 bytes, Status: OK [1,15] Written, Length: 30 bytes, Status: OK [1,16] Written, Length: 30 bytes, Status: OK [1,17] Written, Length: 30 bytes, Status: OK [1,18] Written, Length: 30 bytes, Status: OK [1,19] Written, Length: 30 bytes, Status: OK [1,22] Written, Length: 24 bytes, Status: OK [1,26] Written, Length: 10 bytes, Status: OK [1,27] Written, Length: 36 bytes, Status: OK [1,28] Written, Length: 110 bytes, Status: OK [1,29] Written, Length: 10 bytes, Status: OK [1,30] Written, Length: 36 bytes, Status: OK [1,31] Written, Length: 24 bytes, Status: OK [1,32] Written, Length: 216 bytes, Status: OK [1,33] Written, Length: 36 bytes, Status: OK [1,35] Written, Length: 24 bytes, Status: OK [1,36] Written, Length: 24 bytes, Status: OK [1,38] Written, Length: 216 bytes, Status: OK [1,39] Written, Length: 36 bytes, Status: OK [1,40] Written, Length: 24 bytes, Status: OK [1,41] Written, Length: 216 bytes, Status: OK [1,43] Written, Length: 36 bytes, Status: OK [1,44] Written, Length: 216 bytes, Status: OK [1,45] Written, Length: 216 bytes, Status: OK [309,0] Written, Length: 4 bytes, Status: OK [309,1] Written, Length: 2 bytes, Status: OK [309,2] Written, Length: 12 bytes, Status: OK [309,3] Written, Length: 36 bytes, Status: OK [309,4] Written, Length: 12 bytes, Status: OK [309,7] Written, Length: 12 bytes, Status: OK [309,17] Written, Length: 12 bytes, Status: OK Write PM Finished, Record written OK: 38, Record written NOT OK: 0 Лог Cyclone Box, Security Analyse: Started Phone Security Analysis... MCU Version V 92_11w25.1 MCU Date 01-07-11 Product RM-718 (Nokia C6-01) Manufacturer (c) Nokia IMEI 35xxxxxxxxxxxxxxxxx Mastercode 145263546 Reading Security Block... Security block OK and saved to "RM-718_35xxxxxxxxxxx_14.11.2011_22629.SecurityBlock.PM" Step 1 : Testing SIMLOCK SIMLOCK SEFLTEST PASSED OK! Step 2 : Testing SECURITY -- SECURITY PROBLEM -- Phone have failed SECURITY Test, that means Superdongle Area is DAMAGED! To repair it, simply slick "SX4 Authorization / SD Repair" button. After SX4/SD Repair, don't forget to write PM file with fields 1,309 (if SW don't do this automatically) Additionaly, Checking HWC/CCC Certs... Booting CMT... CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104 CMT_EM_ASIC_ID: 00001040 CMT_EM_ASIC_ID: 00001030 CMT_PUBLIC_ID: 0F40020C66AC03225A84B9358468328C9FF6D9A0 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B CMT_BOOT_ROM_CRC: E693EF0D CMT_SECURE_ROM_CRC: AC22615B CMT Ready! Searching for BootCode: DualLine 32Bit RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.16.0, Algo: BB5 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR FlashChip[0,CMT]: 0x00EC006000000032, Samsung, ONENAND Requested Algorithm: XSR 1.6 (CMT) Searching for BootCode: DualLine 32Bit FlashChip 0x00EC0060 (Samsung), Size: 1024MBytes, VPP: Not Supported RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.16.0, Algo: XSR 1.6 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: A676DE8B3DEA6D6C6FFE9CBE15A7C501CC822B23 APE Subsystem Not Found Flashbus Write baud set to 5.0Mbits HWC Looks OK! CCC Looks OK! Restarting MCU... -- SECURITY PROBLEM -- Step 3 : Analyzing Security Block "0F40020C66AC03225A84B9358468328C9FF6D9A0.C0004076" Exists, That is good... Checking SUPERDONGLE... SUPERDONGLE FOUND AND CHECKSUM OK! PASSED! Checking SIMLOCK... Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?) Checking MCU&DSP TIMESTAMPS... MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED! Checking CMLA KEYS... CMLA KEYS FOUND AND CHECKSUM OK! PASSED! Checking ECC KEYS... ECC KEYS FOUND AND CHECKSUM OK! PASSED! Checking DIV KEYS... DIV KEYS FOUND AND CHECKSUM OK! PASSED! Analyze finished!

16.11.2011, 19:33	#7
Shuhauz Senior Member Регистрация: 19.04.2011 Сообщений: 304 Вес репутации: 79	Re: Nokia C6-01 RM-718 после неудачной прошивки Сделал я этот тело.Слил с рабочего тела и залил HWC+CCC.Тему мона закрыть!!!! Последний раз редактировалось Shuhauz; 16.11.2011 в 20:45.