 |
 |
 |
 |
|
|
|
|||||||
| Nokia Программный и Аппаратный ремонт телефонов Nokia |
 |
|
|
Опции темы | Поиск в этой теме |
24.11.2011, 14:24
|
#1 |
|
Member
Регистрация: 24.11.2011
Адрес: Самара
Сообщений: 85
Вес репутации: 36   |
N96, после даунгрейда не включается 100% софт
Приветствую, Уважаемые пользователи сайта, требуется квалифицированная помощь..
Есть Nokia N96 , требовалась замена ПО, труба 100% исправная, заменил ПО, по глупости на последнюю версию ПО - SW 30.101 , но она без русского языка.. Что есть из боксов: UFS,Cyclone, MX-key(свисток), BEST Что проделано: В Циклоне выбрал галочки  Лью прошивку - 30.033 лог:Booting CMT...
APE_SYSTEM_ASIC_ID: 008815D3 APE_ASIC_MODE_ID: 00 APE_PUBLIC_ID: 8F51FBF79D941A785434064E963B2C9B0A109223 APE_ROOT_KEY_HASH: 0BBC4203E2D3B82504C75CB65E906A35 APE_BOOT_ROM_CRC: 137A9A3B APE_SECURE_ROM_CRC: 33259D2C CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103 CMT_EM_ASIC_ID: 00000295 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 0ED0001316AE0158B416060BAFE342496AC77FD5 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE CMT_BOOT_ROM_CRC: 4B9B7510 CMT_SECURE_ROM_CRC: 3E691FF8 CMT Ready! Searching for BootCode: DualLine 32Bit RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x00012C7E00006921, AMD, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR Searching for BootCode: DualLine 32Bit FlashChip 0x00012C7E (AMD), Size: 16MBytes, VPP: 9V RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.5 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: AD7799ABC45695918C0B8E955FAD5FF12650E6AE APE Boot skipped on user request Flashbus Write baud set to 5.0Mbits Restarting MCU... Processing pre flash tasks... Backing up RPL... RPL Creation started... Processing CMT Part... Storing Product Code... Storing PSN... Storing HWID... Trying to store Simlock... Reading Configuration Key... Hashing... Reading SHA1-RSA Signature... Reading SHA1-HMAC Signature... Storing Simlock... Trying to store WMDRM RPL... Reading Keys... Storing WMDRM PD... Reading Security Block... Security block OK and saved to "RM-247_356406021347165_24.11.2011_145443.SecurityBlock.PM" WARNING: "0ED0001316AE0158B416060BAFE342496AC77FD5.C0003918" Not Exists, Will read it... Reading CYC file from phone... Booting CMT... APE_SYSTEM_ASIC_ID: 008815D3 APE_ASIC_MODE_ID: 00 APE_PUBLIC_ID: 8F51FBF79D941A785434064E963B2C9B0A109223 APE_ROOT_KEY_HASH: 0BBC4203E2D3B82504C75CB65E906A35 APE_BOOT_ROM_CRC: 137A9A3B APE_SECURE_ROM_CRC: 33259D2C CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103 CMT_EM_ASIC_ID: 00000295 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 0ED0001316AE0158B416060BAFE342496AC77FD5 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE CMT_BOOT_ROM_CRC: 4B9B7510 CMT_SECURE_ROM_CRC: 3E691FF8 CMT Ready! New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.16.0, Algo: BB5 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x00012C7E00006921, AMD, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR Sending Auxiliary Loader... Auxiliary Loader Sent! If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. Loader: RAPxx CommonBoot v1.06 (C) 2011 KarwosLabs Custom loader running OK! Working... Readed OK, Saving to "0ED0001316AE0158B416060BAFE342496AC77FD5.C0003918" Storing Additional Data... Checking Superdongle Key... Encrypting Superdongle Key... Storing Superdongle Key... Checking CMLA Key... Storing CMLA Key... Booting CMT... APE_SYSTEM_ASIC_ID: 008815D3 APE_ASIC_MODE_ID: 00 APE_PUBLIC_ID: 8F51FBF79D941A785434064E963B2C9B0A109223 APE_ROOT_KEY_HASH: 0BBC4203E2D3B82504C75CB65E906A35 APE_BOOT_ROM_CRC: 137A9A3B APE_SECURE_ROM_CRC: 33259D2C CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103 CMT_EM_ASIC_ID: 00000295 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 0ED0001316AE0158B416060BAFE342496AC77FD5 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE CMT_BOOT_ROM_CRC: 4B9B7510 CMT_SECURE_ROM_CRC: 3E691FF8 CMT Ready! Searching for BootCode: DualLine 32Bit RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5 Flashbus Write baud set to 1.0Mbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x00012C7E00006921, AMD, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR Searching for BootCode: DualLine 32Bit FlashChip 0x00012C7E (AMD), Size: 16MBytes, VPP: 9V RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.5 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Searching for BootCode: DualLine 32Bit STn8815_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.14.0, Algo: BB5 Adding FUR Client (APE, State: Start)... APE FUR Ready! If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,APE]: 0x0000000000000000, Unknown, RAM FlashChip[0,APE]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,APE]: 0x002000B100000000, ST, ONENAND Searching for BootCode: DualLine 32Bit FlashChip 0x002000B1 (ST), Size: 8MBytes, VPP: 21V STn8815_STNFMS_alg.fg, Type: Algorithm, Rev: 512.11.14.0, Algo: N8815 ALG STNFMS Initializing TurboCache... TurboCache Loaded! Writing APE KEYS Certificate... Writing APE PASUBTOC Certificate... Writing APE ALG Certificate... APE Algorithm Ready! Adding FUR Client (APE, State: Ready)... APE FUR Ready! Box VPP disabled Internal APE Phone VPP Enabled PAPUBKEYS Hash for APE: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Flashbus Write baud set to 5.0Mbits Storing NPC... Storing CCC... Storing HWC... Storing VARIANT... Processing APE Part... Storing Product Code... Storing PSN... Storing HWID... Storing NPC... Storing CCC... Storing HWC... APE VARIANT Not Found Restarting MCU... RPL Saved OK RPL backup thread finished, continuing... Backing up simlock... Simlock backup problem -> Phone not detected Backup simlock thread finished, continuing... Applying downgrade patch... Apply downgrade patch failed -> Phone not detected Pre flash tasks finished, continuing... Processing RM-247_30.033_prd.core.fpsx (CMT)... Booting CMT... APE_SYSTEM_ASIC_ID: 008815D3 APE_ASIC_MODE_ID: 00 APE_PUBLIC_ID: 8F51FBF79D941A785434064E963B2C9B0A109223 APE_ROOT_KEY_HASH: 0BBC4203E2D3B82504C75CB65E906A35 APE_BOOT_ROM_CRC: 137A9A3B APE_SECURE_ROM_CRC: 33259D2C CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103 CMT_EM_ASIC_ID: 00000295 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 0ED0001316AE0158B416060BAFE342496AC77FD5 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE CMT_BOOT_ROM_CRC: 4B9B7510 CMT_SECURE_ROM_CRC: 3E691FF8 CMT Ready! RM-247_30.033_prd.core.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5, N8815 ALG STNFMS, BB5 Searching for BootCode: DualLine 32Bit RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5 Flashbus Write baud set to 51Kbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x00012C7E00006921, AMD, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR Searching for BootCode: DualLine 32Bit FlashChip 0x00012C7E (AMD), Size: 16MBytes, VPP: 9V RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.5 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Flashbus Write baud set to 5.0Mbits Sending Certificates... Certificates OK Partitioning... Partitioning OK Started group flash erase EraseArea[0,CMT]: 0x00080000-0x007A6EE9, NOR EraseArea[0,CMT]: 0x00000000-0x0005FFFF, NOR EraseArea[0,CMT]: 0x00880000-0x00EFFFFF, NOR Waiting 320s for erasure finish... Erase taken 31.938s Writing all blocks... Initializing TurboCache... TurboCache Loaded! Writing CMT NOLO Certificate... Writing CMT KEYS Certificate... Writing CMT PRIMAPP Certificate... Writing CMT PASUBTOC Certificate... Writing CMT PAPUBKEYS Certificate... Writing CMT UPDAPP Certificate... Writing CMT DSP0 Certificate... Writing CMT MCUSW Certificate... Programming Status OK! All blocks written OK! Time taken 32.656s Flashing Speed: 25002,19 kBit/S Restarting MCU... Processing RM-247_30.033_prd.core.fpsx (APE)... Booting CMT... APE_SYSTEM_ASIC_ID: 008815D3 APE_ASIC_MODE_ID: 00 APE_PUBLIC_ID: 8F51FBF79D941A785434064E963B2C9B0A109223 APE_ROOT_KEY_HASH: 0BBC4203E2D3B82504C75CB65E906A35 APE_BOOT_ROM_CRC: 137A9A3B APE_SECURE_ROM_CRC: 33259D2C CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103 CMT_EM_ASIC_ID: 00000295 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 0ED0001316AE0158B416060BAFE342496AC77FD5 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE CMT_BOOT_ROM_CRC: 4B9B7510 CMT_SECURE_ROM_CRC: 3E691FF8 CMT Ready! RM-247_30.033_prd.core.fpsx, Type: Flash Image, Algo: BB5, XSR 1.5, N8815 ALG STNFMS, BB5 Searching for BootCode: DualLine 32Bit RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5 Flashbus Write baud set to 51Kbits Flashbus Read baud set to 98Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x00012C7E00006921, AMD, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR Searching for BootCode: DualLine 32Bit FlashChip 0x00012C7E (AMD), Size: 16MBytes, VPP: 9V RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.5 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Searching for BootCode: DualLine 32Bit STn8815_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.14.0, Algo: BB5 Adding FUR Client (APE, State: Start)... APE FUR Ready! If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,APE]: 0x0000000000000000, Unknown, RAM FlashChip[0,APE]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,APE]: 0x002000B100000000, ST, ONENAND Searching for BootCode: DualLine 32Bit FlashChip 0x002000B1 (ST), Size: 8MBytes, VPP: 21V STn8815_STNFMS_alg.fg, Type: Algorithm, Rev: 512.11.14.0, Algo: N8815 ALG STNFMS Initializing TurboCache... TurboCache Loaded! Writing APE KEYS Certificate... Writing APE PASUBTOC Certificate... Writing APE ALG Certificate... APE Algorithm Ready! Adding FUR Client (APE, State: Ready)... APE FUR Ready! Box VPP disabled Internal APE Phone VPP Enabled PAPUBKEYS Hash for APE: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Flashbus Write baud set to 5.0Mbits Sending Certificates... Certificates OK Partitioning... Partitioning OK Started group flash erase EraseArea[0,APE]: 0x00000000-0x0007FFFF, NAND EraseArea[0,APE]: 0x00080000-0x000BFFFF, NAND EraseArea[0,APE]: 0x000E0000-0x0045FFFF, NAND EraseArea[0,APE]: 0x00840000-0x0A8FFFFF, NAND Waiting 320s for erasure finish... Erase taken 2.547s Writing all blocks... Initializing TurboCache... TurboCache Loaded! Writing APE X-LOADER Certificate... Writing APE KEYS Certificate... Writing APE PRIMAAPP Certificate... Writing APE SOS*UPDAPP Certificate... Writing APE SOS+XZIP Certificate... Writing APE PASUBTOC Certificate... Writing APE PAPUBKEYS Certificate... Writing APE SOS+CORE Certificate... Writing APE SOS+ROFS1 Certificate... Programming Status OK! All blocks written OK! Time taken 176.94s Flashing Speed: 4636,57 kBit/S Restarting MCU... Processing RM-247_30.033_022.1_prd.language.fpsx (CMT)... Processing RM-247_30.033_022.1_prd.language.fpsx (APE)... Booting CMT... APE_SYSTEM_ASIC_ID: 008815D3 APE_ASIC_MODE_ID: 00 APE_PUBLIC_ID: 8F51FBF79D941A785434064E963B2C9B0A109223 APE_ROOT_KEY_HASH: 0BBC4203E2D3B82504C75CB65E906A35 APE_BOOT_ROM_CRC: 137A9A3B APE_SECURE_ROM_CRC: 33259D2C CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103 CMT_EM_ASIC_ID: 00000295 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 0ED0001316AE0158B416060BAFE342496AC77FD5 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE CMT_BOOT_ROM_CRC: 4B9B7510 CMT_SECURE_ROM_CRC: 3E691FF8 CMT Ready! RM-247_30.033_022.1_prd.language.fpsx, Type: Flash Image, Algo: N8815 ALG STNFMS, BB5, XSR 1.5, BB5 Searching for BootCode: DualLine 32Bit RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 100Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x00012C7E00006921, AMD, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR Searching for BootCode: DualLine 32Bit FlashChip 0x00012C7E (AMD), Size: 16MBytes, VPP: 9V RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.5 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Searching for BootCode: DualLine 32Bit STn8815_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.14.0, Algo: BB5 Adding FUR Client (APE, State: Start)... APE FUR Ready! If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,APE]: 0x0000000000000000, Unknown, RAM FlashChip[0,APE]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,APE]: 0x002000B100000000, ST, ONENAND Searching for BootCode: DualLine 32Bit FlashChip 0x002000B1 (ST), Size: 8MBytes, VPP: 21V STn8815_STNFMS_alg.fg, Type: Algorithm, Rev: 512.11.14.0, Algo: N8815 ALG STNFMS Initializing TurboCache... TurboCache Loaded! Writing APE KEYS Certificate... Writing APE PASUBTOC Certificate... Writing APE ALG Certificate... APE Algorithm Ready! Adding FUR Client (APE, State: Ready)... APE FUR Ready! Box VPP disabled Internal APE Phone VPP Enabled PAPUBKEYS Hash for APE: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Flashbus Write baud set to 5.0Mbits Started group flash erase EraseArea[0,APE]: 0x07780000-0x099FFFFF, NAND Waiting 320s for erasure finish... Erase taken 0.578s Writing all blocks... Initializing TurboCache... TurboCache Loaded! Writing APE SOS+ROFS2 Certificate... Programming Status OK! All blocks written OK! Time taken 31.188s Flashing Speed: 4315,43 kBit/S Restarting MCU... Processing RM-247_30.033_100.1_prd.uda.fpsx (CMT)... Processing RM-247_30.033_100.1_prd.uda.fpsx (APE)... Booting CMT... APE_SYSTEM_ASIC_ID: 008815D3 APE_ASIC_MODE_ID: 00 APE_PUBLIC_ID: 8F51FBF79D941A785434064E963B2C9B0A109223 APE_ROOT_KEY_HASH: 0BBC4203E2D3B82504C75CB65E906A35 APE_BOOT_ROM_CRC: 137A9A3B APE_SECURE_ROM_CRC: 33259D2C CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103 CMT_EM_ASIC_ID: 00000295 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 0ED0001316AE0158B416060BAFE342496AC77FD5 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE CMT_BOOT_ROM_CRC: 4B9B7510 CMT_SECURE_ROM_CRC: 3E691FF8 CMT Ready! RM-247_30.033_100.1_prd.uda.fpsx, Type: Flash Image, Algo: N8815 ALG STNFMS, BB5, XSR 1.5, BB5 Searching for BootCode: DualLine 32Bit RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 100Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x00012C7E00006921, AMD, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR Searching for BootCode: DualLine 32Bit FlashChip 0x00012C7E (AMD), Size: 16MBytes, VPP: 9V RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.5 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Searching for BootCode: DualLine 32Bit STn8815_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.14.0, Algo: BB5 Adding FUR Client (APE, State: Start)... APE FUR Ready! If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,APE]: 0x0000000000000000, Unknown, RAM FlashChip[0,APE]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,APE]: 0x002000B100000000, ST, ONENAND Searching for BootCode: DualLine 32Bit FlashChip 0x002000B1 (ST), Size: 8MBytes, VPP: 21V STn8815_STNFMS_alg.fg, Type: Algorithm, Rev: 512.11.14.0, Algo: N8815 ALG STNFMS Initializing TurboCache... TurboCache Loaded! Writing APE KEYS Certificate... Writing APE PASUBTOC Certificate... Writing APE ALG Certificate... APE Algorithm Ready! Adding FUR Client (APE, State: Ready)... APE FUR Ready! Box VPP disabled Internal APE Phone VPP Enabled PAPUBKEYS Hash for APE: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Flashbus Write baud set to 5.0Mbits Started group flash erase Erase Partition (APE) Waiting 320s for erasure finish... Erase taken 1.422s Writing all blocks... Initializing TurboCache... TurboCache Loaded! Programming Status OK! All blocks written OK! Time taken 25.16s Flashing Speed: 4309,27 kBit/S Restarting MCU... Processing RM-247_30.033_098.1_prd.customer.fpsx (CMT)... Processing RM-247_30.033_098.1_prd.customer.fpsx (APE)... Booting CMT... APE_SYSTEM_ASIC_ID: 008815D3 APE_ASIC_MODE_ID: 00 APE_PUBLIC_ID: 8F51FBF79D941A785434064E963B2C9B0A109223 APE_ROOT_KEY_HASH: 0BBC4203E2D3B82504C75CB65E906A35 APE_BOOT_ROM_CRC: 137A9A3B APE_SECURE_ROM_CRC: 33259D2C CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101031103 CMT_EM_ASIC_ID: 00000295 CMT_EM_ASIC_ID: 00000B22 CMT_PUBLIC_ID: 0ED0001316AE0158B416060BAFE342496AC77FD5 CMT_ASIC_MODE_ID: 00 CMT_ROOT_KEY_HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE CMT_BOOT_ROM_CRC: 4B9B7510 CMT_SECURE_ROM_CRC: 3E691FF8 CMT Ready! RM-247_30.033_098.1_prd.customer.fpsx, Type: Flash Image, Algo: N8815 ALG STNFMS, BB5, XSR 1.5, BB5 Searching for BootCode: DualLine 32Bit RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5 Flashbus Write baud set to 650Kbits Flashbus Read baud set to 100Kbits Using NEW BB5 FLASHING PROTOCOL Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,CMT]: 0x00012C7E00006921, AMD, NOR FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR Searching for BootCode: DualLine 32Bit FlashChip 0x00012C7E (AMD), Size: 16MBytes, VPP: 9V RAPIDOv11_XSR15_alg.fg, Type: Algorithm, Rev: 512.10.48.1, Algo: XSR 1.5 Initializing TurboCache... TurboCache Loaded! Writing CMT PASUBTOC Certificate... Writing CMT ALG Certificate... CMT Algorithm Ready! Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit Box TX2 Data Pin set to: Service Pin 3 Adding FUR Client (CMT, State: Ready)... CMT FUR Ready! Box VPP disabled Internal CMT Phone VPP Enabled PAPUBKEYS Hash for CMT: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Searching for BootCode: DualLine 32Bit STn8815_2nd.fg, Type: 2nd Boot Loader, Rev: 512.11.14.0, Algo: BB5 Adding FUR Client (APE, State: Start)... APE FUR Ready! If software STUCK HERE with box TX LED lit, that means: 1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!) 2. Your cable is not TX2 Enabled! 3. Transmission error occured, try again In either cases, you need to reconnect your box from USB. FlashChip[0,APE]: 0x0000000000000000, Unknown, RAM FlashChip[0,APE]: 0xFFFF000000000000, Unknown, MMC FlashChip[0,APE]: 0x002000B100000000, ST, ONENAND Searching for BootCode: DualLine 32Bit FlashChip 0x002000B1 (ST), Size: 8MBytes, VPP: 21V STn8815_STNFMS_alg.fg, Type: Algorithm, Rev: 512.11.14.0, Algo: N8815 ALG STNFMS Initializing TurboCache... TurboCache Loaded! Writing APE KEYS Certificate... Writing APE PASUBTOC Certificate... Writing APE ALG Certificate... APE Algorithm Ready! Adding FUR Client (APE, State: Ready)... APE FUR Ready! Box VPP disabled Internal APE Phone VPP Enabled PAPUBKEYS Hash for APE: AD7799ABC45695918C0B8E955FAD5FF12650E6AE Flashbus Write baud set to 5.0Mbits Started group flash erase EraseArea[0,APE]: 0x09A00000-0x0A8FFFFF, NAND Waiting 320s for erasure finish... Erase taken 0.265s Writing all blocks... Initializing TurboCache... TurboCache Loaded! Writing APE SOS+ROFS3 Certificate... Programming Status OK! All blocks written OK! Time taken 0.172s Flashing Speed: 256,23 kBit/S Restarting MCU... All images processed OK! Processing post flash tasks... Setting Factory Defaults... Factory defaults OK Труба прошилась, локала нет, при включении моргает белым и не включается, требуется помощь, бэкап есть циклоновский список файлов: RM-247_356406021347165_24.11.2011_145443.SecurityBloc k - расширение PM RM-247_35640602134716524.11.2011_145438 - расширение RPL Метод и пушек по воробьям не предлагать, ранее пользовался им для N96 - НЕ катит. Жду советов , Уважаемые форумчане |
|
|
|
24.11.2011, 14:27
|
#2 |
|
ADMINISTRATOR
Регистрация: 01.01.2011
Адрес: www.UO5OQ.com
Сообщений: 14,724
Вес репутации: 10  |
Re: N96, после даунгрейда не включается 100% софт
- Запишите снова SW 30.101, что бы телефон полностью ожил.
- Запишите только русский PPM от SW 30.033 Должно получиться.
__________________
Разблокировка iPhone, NCK Коды, Логи и Активации на www.UO5OQ.com |
|
|
|
| Пользователь сказал cпасибо: | Jeka-777 (24.11.2011) |
|
24.11.2011, 14:31
|
#3 | |
|
Member
Регистрация: 24.11.2011
Адрес: Самара
Сообщений: 85
Вес репутации: 36 |
Re: N96, после даунгрейда не включается 100% софт
Цитата:
|
|
|
|
|
|
24.11.2011, 14:41
|
#4 |
|
ADMINISTRATOR
Регистрация: 01.01.2011
Адрес: www.UO5OQ.com
Сообщений: 14,724
Вес репутации: 10 |
Re: N96, после даунгрейда не включается 100% софт
Сделайте всевозможные бэкапы сначала (если ещё не поздно после понижения).
А при повышении ничего не должно слететь.
__________________
Разблокировка iPhone, NCK Коды, Логи и Активации на www.UO5OQ.com |
|
|
|
| Пользователь сказал cпасибо: | Jeka-777 (24.11.2011) |
|
24.11.2011, 15:08
|
#5 | |
|
Member
Регистрация: 24.11.2011
Адрес: Самара
Сообщений: 85
Вес репутации: 36 |
Re: N96, после даунгрейда не включается 100% софт
Цитата:
Вот лог восстановленого и русифицированого N96MCU Version V ICPR72_09w13.3
MCU Date 15-09-09 Product RM-247 (Nokia N96) Manufacturer (c) Nokia IMEI 356406021347165 Mastercode 30462165 IMEI Spare 3A65040612431706 IMEI SV 3365040612431716F0000000 PPM 0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002ҐV 40.2009.39.xx PRD CNT V 40.2009.39.xx PRD PSN CUB609624 Product Code 0543722 Basic Product Code 0542934 PSD 0000000000000000 LPSN 0 WLAN MAC 0022FC8FA7FC APE SW 30.101 APE Variant 30.10130.033.009.130.101.098.1 APE Test 4032_PR10.0832_034_002 APE HW 0 APE ADSP 0 RETU 15 TAHVO 22 AHNE 11 HW 1001o0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002ҐV 40.2009.39.xx PRD PCI o0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002ҐV 40.2009.39.xx PRD UEM 0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002ҐV 40.2009.39.xx PRD UPP 0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002ҐV 40.2009.39.xx PRD RFIC 17141715 DSP MC_4032_ICPR72_09w13o0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002 LCD 0n0W2724187i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002 BT 0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002 ADSP Sw 0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002ҐV 40.2009.39.xx PRD ADSP DevID 0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002ҐV 40.2009.39.xx PRD ADSP RevID 0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002ҐV 40.2009.39.xx PRD AEM 0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002ҐV 40.2009.39.xx PRD Flip MCUSW 0n0i30.101j$30.10130.033.009.130.101.098.1rV 40.2009.39.xx PRDk4032_PR10.0832_034_002 Simlock Server SIMLOCK SERVER Simlock Key 2440700000000000 Simlock Profile 8000000000000006 Simlock Key Cnt 0 Simlock FBUS Cnt 0 Simlock [1,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [1,2] State: OPENED Type: GID Data: FFFF Simlock [1,3] State: OPENED Type: GID Data: FFFF Simlock [1,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [1,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [2,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [2,2] State: OPENED Type: GID Data: FFFF Simlock [2,3] State: OPENED Type: GID Data: FFFF Simlock [2,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [2,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [3,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [3,2] State: OPENED Type: GID Data: FFFF Simlock [3,3] State: OPENED Type: GID Data: FFFF Simlock [3,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [3,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [4,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [4,2] State: OPENED Type: GID Data: FFFF Simlock [4,3] State: OPENED Type: GID Data: FFFF Simlock [4,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [4,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [5,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [5,2] State: OPENED Type: GID Data: FFFF Simlock [5,3] State: OPENED Type: GID Data: FFFF Simlock [5,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [5,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [6,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [6,2] State: OPENED Type: GID Data: FFFF Simlock [6,3] State: OPENED Type: GID Data: FFFF Simlock [6,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [6,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [7,1] State: OPENED Type: MCC-MNC Data: FFFFFF Simlock [7,2] State: OPENED Type: GID Data: FFFF Simlock [7,3] State: OPENED Type: GID Data: FFFF Simlock [7,4] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Simlock [7,5] State: OPENED Type: IMSI Data: FFFFFFFFFFFFFFFF Auto Selecting Flash Files on User Request... Product Code: 0543722 Scanning avaiable products... Processing C:\Program Files\Nokia\Phoenix\Products\... Found 85 products, Filtering DCT4 Products - wait... 0 Products left after filtering. Ready. Scanning avaiable products... Processing C:\Program Files\Nokia\Phoenix\Products\... Found 85 products, Filtering BB5 Products - wait... 5 Products left after filtering. Ready. No Flash Datapackage installed for this Phone! |
|
|
|
|
