6730c-1 dead после прошивки!

[bio23XX04M]

записал в rm-547 прошивку от rm-566
убыл....затер....прошил правильной rm-547...но записать RPL не могу(((

вот лог очень срочно:

Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104
CMT_EM_ASIC_ID: 00000C34
CMT_EM_ASIC_ID: 00000C30
CMT_PUBLIC_ID: 15200104675B0344F09A0135D3F0EA8327CBBC87
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC: 3E273BF6
CMT_SECURE_ROM_CRC: 37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.40.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020004000000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020004000000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.40.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: DA2DB2D32C1B2D9886A55B5D8A14F19ADDC53128
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Restarting MCU...
MCU Version V ICPR82_09w39.1
MCU Date 06-10-09
Product RM-547 (Nokia 6730 classic)
Manufacturer (c) Nokia
IMEI 12345610654321?
IMEI Spare 1A32541660452301
IMEI SV 1332541660452321F8000000
PSN CLF541376
Product Code 0583025
Basic Product Code 0574520
PSD 0000000000000000
LPSN 0
APE SW 023.010
APE Variant 023.010023.010.05.01
APE HW 256
APE ADSP 256
APE BT HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.
RETU 34
TAHVO 00
AHNE 11
HW 0500
RFIC |Vapaus_5.1 | Aura_?.?
DSP ICPR82_09w39.1_RIO
Failed to read info -> Failed to read SP info
Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
Writing Product Code...
Writing PSN...
Writing HWID...
Writing Simlock...
Handling as SL3 Simlock Data
Handling as SIMLOCK1 Format
Reading Security Block...
Security block OK and saved to "RM-547_12345610654321_12.01.2012_184046.SecurityBlock.PM"
15 Digits NCK Found
Simlock ACCEPTED OK !
Writing Superdongle key...
Superdongle Key ACCEPTED OK !
Writing CMLA key...
Failed to Write RPL File -> Phone is not responding for Superdongle Request

[UO5OQ]

Сообщение от bio23XX04M

записал в rm-547 прошивку от rm-566
убыл....затер....прошил правильной rm-547...но записать RPL не могу(((

вот лог очень срочно:

Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102011104
CMT_EM_ASIC_ID: 00000C34
CMT_EM_ASIC_ID: 00000C30
CMT_PUBLIC_ID: 15200104675B0344F09A0135D3F0EA8327CBBC87
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 25B977A055BE9B5DEC0C38A2A279C695
CMT_BOOT_ROM_CRC: 3E273BF6
CMT_SECURE_ROM_CRC: 37BE26FA
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.11.40.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using NEW BB5 FLASHING PROTOCOL
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020004000000031, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020004000000031, ST, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
FlashChip 0x00200040 (ST), Size: 256MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.11.40.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: DA2DB2D32C1B2D9886A55B5D8A14F19ADDC53128
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Restarting MCU...
MCU Version V ICPR82_09w39.1
MCU Date 06-10-09
Product RM-547 (Nokia 6730 classic)
Manufacturer (c) Nokia
IMEI 12345610654321?
IMEI Spare 1A32541660452301
IMEI SV 1332541660452321F8000000
PSN CLF541376
Product Code 0583025
Basic Product Code 0574520
PSD 0000000000000000
LPSN 0
APE SW 023.010
APE Variant 023.010023.010.05.01
APE HW 256
APE ADSP 256
APE BT HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12652.
RETU 34
TAHVO 00
AHNE 11
HW 0500
RFIC |Vapaus_5.1 | Aura_?.?
DSP ICPR82_09w39.1_RIO
Failed to read info -> Failed to read SP info
Skipping RPL decryption...
Parsing decrypted RPL...
Processing FBUS Part...
Writing Product Code...
Writing PSN...
Writing HWID...
Writing Simlock...
Handling as SL3 Simlock Data
Handling as SIMLOCK1 Format
Reading Security Block...
Security block OK and saved to "RM-547_12345610654321_12.01.2012_184046.SecurityBlock.PM"
15 Digits NCK Found
Simlock ACCEPTED OK !
Writing Superdongle key...
Superdongle Key ACCEPTED OK !
Writing CMLA key...
Failed to Write RPL File -> Phone is not responding for Superdongle Request

Не можете записать сделаный вами RPL бэкап или заказаный RPL ?
Как внешне ведёт себя телефон сейчас ?

[bio23XX04M]

было start-up failed...но сейчас нокиа ....блык ...и все !!!
прописью eno файла поднимаю снова к старт-ап фейлед....но рпл не пишет смтр. лог

[UO5OQ]

Сообщение от bio23XX04M

было start-up failed...но сейчас нокиа ....блык ...и все !!!
прописью eno файла поднимаю снова к старт-ап фейлед....но рпл не пишет смтр. лог

Не пишет сделаный вами бэкап RPL или заказаный RPL ?
Кроме Cyclone есть ещё чем записать RPL ?

[bio23XX04M]

рпл сохранена с полностю роб тела!!! все блоки вроде норм сохр. циклон после проши делает фактори дефал - значит в локал мает входить...но входит только циклоном ---мх-бокс в локал не вганяет рпл не пише...сейчас пробую бестом(((

лог BEST:

Preparing for write certificates...

CMT : CCC erase Ok
Writing CCC... Ok

CMT : HWC erase Ok
Writing HWC... Ok


Done!

Reading Phone Info....
Connected phone - Error
Software ver : Error
IMEI : Error
Ape Ver : Error
APE Var : Error
APE ADSP: Error
DSP Ver : Error
APE Test: Error
PPM : Error
CNT : Error
Product SN : Error
Product code : Error
Base Prd.code: Error
Module code : Error
Long Prod.SN : Error
Hardware info=======
HWID : Error
Retu : Error
Tahvo : Error
Batery: 8189 mV
Camera:
CMT BT: Error
APE BT: Error
APE HW: Error
LCDVer: Error
RF ic : Error
Lock info ===========
IMEI : Error
IMEI spNet :
IMEI svNet :

Unable to read Lock table...
Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
SimLock Data found!
SimLock key found!
SuperDongle Key found!
CMLA key found!
WMDRM key found!
Setting FlashMode
FlashMode set Ok
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000030000022600010007600C192102011104
CMT EM0 ID : 00000C34
CMT EM1 ID : 00000C30
CMT PUB ID : 15200104675B0344F09A0135D3F0EA8327CBBC87
CMT MODE ID : 00
CMT R_HASH : 25B977A055BE9B5DEC0C38A2A279C695
CMT ROM ID : 3E273BF637BE26FA

CMT : Sending 2nd loader...
Use : RAPUv11_2nd.fg , Rev : 0.0 Ver : 1.37.1
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 00400020 , CMT , NOR
CMT Flash ID : 00400020 < ST => M39BORBOAD
FLCNT : 0000003D0168304D30ABB5B101F018D1089902
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAPUv11_algo_xsr16.fg , Rev : 0.0 Ver : 1.40.0
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode : Dual (Ddr, TX2)

Boot Done!

Preparing for write certificates...

Switching to CMT...

CMT : NPC erase Ok
Writing NPC... Ok

CMT : CCC erase Ok
Writing CCC... Ok

CMT : HWC erase Ok
Writing HWC... Ok


Init Service mode... Wait...


Writing SimLock Key... Error!
Writing SimLock Data... Error!
Writing Super Dongle Key... Ok

SDD Key status : read data error
SimLock status : SimLock Damaged!!!!!
Security status : Security Damaged!!!!!


Done!

Connect phone on selected interface...

[UO5OQ]

Логи скрывайте тегом SPOILER - его значёк в панели редактировани/создания сообщения

SLD почему-то не пишется у вас ни Cyclone ни BEST.
Приложите сделаные бэкапы, я посмотрю всё ли там на месте.

[bio23XX04M]

zdes' orig rpl

[UO5OQ]

Сообщение от bio23XX04M

zdes' orig rpl

Полностью проверить RPL на валидность нельзя никак и нигде. Но на вид он вполне нормальный.

После полного стирания и записи только прошивки (SW), телефон включается полностью и работает с IMEI 123456... ?

[bio23XX04M]

затер циклоном все flash chip...затем затер все серт eraise all certs...прошил mcu and ppm. mx-box, best(ufs),mt-box -рпл не пошло!!! циклон поправил npc data с 4 раза(ориг рпл) ...сейчас все встало норм, канешно кроме секюрити!!!
-- SECURITY PROBLEM --
Step 3 : Analyzing Security Block
пробую записать 1 и 309 поле не получается...пм-файл брал с акхива uo5oq

[UO5OQ]

Сообщение от bio23XX04M

затер циклоном все flash chip...затем затер все серт eraise all certs...прошил mcu and ppm. mx-box, best(ufs),mt-box -рпл не пошло!!! циклон поправил npc data с 4 раза(ориг рпл) ...сейчас все встало норм, канешно кроме секюрити!!!
-- SECURITY PROBLEM --
Step 3 : Analyzing Security Block
пробую записать 1 и 309 поле не получается...пм-файл брал с акхива uo5oq

Тогда перед SX4 и записью PM, запишите HWC+CCC от этой модели.

[bio23XX04M]

vse idet na OK ...1 and 309 block zapisuvaetsya...no vseravno test failed!
no eto bestom!!!
cyclon ne zapisal 1 and 309 pole...([1,0] Written, Length: 114 bytes, Status: Not accepted, Code: 19)
Pavel est' ideu?
a mogno kakto zapisat' prl chtob nebilo TEST FAILED????

[bio23XX04M]

проблема решена записью 1 и 309 поля МX-box

[Arsen]

Закрыто .